Inhaltsverzeichnis

Migrate MC-LAG to OmniSwitch Virtual-Chassis

Migrate MC-LAG to OmniSwitch Virtual-Chassis

In this TechTip we describe how to successfully migrate from Alcatel-Lucent MC-LAG to Virtual-Chassis. Our experience is that the migration (mainly reload of the switches) takes less than 5 minutes. We recommend to read through this document before you start.

Please validate/check the configuration carefully before you reboot your switches!

Prerequisites

We'll use VIM to automate many, otherwise error-prone, modifications of the configuration.

VIM is an amazing tool and should not be missing on any workstation.

Download for MacOSX: http://code.google.com/p/macvim/
Download for Windows: http://www.vim.org/download.php#pc
Download for Linux: http://www.vim.org/download.php#unix

You should set the following in VIM to highlight the results of „Search & Replace“ as we'll use it throughout the document:

:set hlsearch

On OmniSwitch you'll need the „Advanced“ license to use Virtual-Chassis
Please read carefully through the u-boot / AOS dependencies! Details can be found in the „Upgrade Instructions“.

Comparison of MC-LAG and Virtual-Chassis

MC-LAG	Virtual-Chassis
Available in AOS 7.1.1.R01	Available in AOS 7.3.1.R01
L2-Learning in hardware (MAC-ADDRESS table synchronised across chassis)	L2-Learning in hardware (MAC-ADDRESS table synchronised across chassis)
Independent configuration with separate Management-IP for each switch	Configuration and management of Virtual Chassis is done through one unified IP-Adresse
Independent Bridge-IDs	One Bridge-ID
Independent Routers	One Router
Limited IPv4-L3-Support for MC-LAG (e.g. dynamic routing protocols)	Full support
No IPv6-L3-Support for MC-LAGs (e.g. gateway, dynamic routing)	Full support
Virtual Fabric Link (VFL), fault-tolerant and high-performance Link-Aggregate	Identical
Limited to two chassis	Currently two chassis, soon six
ISSU within the same chassis	ISSU across the chassis

Reasons to migrate from MC-LAG to Virtual-Chassis

simple, unified Management
IPv6-Support
IPv4/IPv6-Routing

Planning the migration

vcsetup.cfg's need to be prepared
MC-LAG and System/Session:
- „multi-chassis“-rows need to be completely removed from configuration
- „session prompt“ needs to be removed from 2nd chassis
- „system name“, „system location“, „system contact“ & „ip interface“ needs to be removed from 2nd chassis
Link-Aggregation:
- „linkagg range“ row needs to be removed from configuration
- linkagg {lacp|static} agg <agg> size <size> admin-state {enable|disable} „multi-chassis active“ needs to be removed from configuration
- linkagg lacp agg <agg> „system-id xx:xx:xx:xx:xx:xx“ needs to be removed from configuration
- linkagg {lacp|static} port „system-id xx:xx:xx:xx:xx:xx“ needs to be removed from configuration
- Convert linkagg {lacp|static} port „slot/port“ to „chassis/slot/port“
VLAN:
- Convert multi-chassis vip-vlan to normal vlan
- Convert VLAN-Assignement of ports tagged/untagged „slot/port“ to „chassis/slot/port“
IP-Interface:
- Either re-use the former virtual IP address (VIP-ADDRESS) as VRRP OR
- Create and use IP-Interface with former „vip-address“ (replace previous „physical IP“ with „vip-address)
- (Remove IP Interfaces from 2nd chassis)
LLDP:
- Convert „slot/port“ to „chassis/slot/port“
Additional configuration
- Verify if there are any configurations in your specific setup that are not handled during this migration?

Prepare for the migration

If not stated otherwise, VIM-commands need to be executed for „Chassis 1“ and „Chassis 2“ configuration.

Convert and remove the Multi-Chassis & VF-Link configuration

At this point we'll remove the multi-chassis configuration. You should store the parameters in a safe place and create new vcsetup.cfg files. In the following we'll see how those kind of files need to look like.

To ease the migration, the following VIM-commands will help us to create the two vcsetup.cfg's:

If you put a „c“ (confirmation) after the „g“ (global), VIM will request a confirmation before replacing each occurrence. If you don't want VIM to do that, simply remove the „c“.

Chassis 1:
:%s/^multi-chassis\ chassis-id\ \(\d\+\)$/virtual-chassis chassis-id \1 configured-chassis-id \1/gc
:%s/^multi-chassis\ vf-link\ create$/virtual-chassis chassis-id 1 vf-link 0 create/gc
:%s/^multi-chassis\ vf-link\ member-port\ \(\d\+\/\S*\)$/virtual-chassis chassis-id 1 vf-link 0 member-port 1\/\1/gc
:%s/^multi-chassis\ chassis-group\ \(\d\+\)$/virtual-chassis chassis-id 1 chassis-group \1/gc

Chassis 2:
:%s/^multi-chassis\ chassis-id\ \(\d\+\)$/virtual-chassis chassis-id \1 configured-chassis-id \1/gc
:%s/^multi-chassis\ vf-link\ create$/virtual-chassis chassis-id 2 vf-link 0 create/gc
:%s/^multi-chassis\ vf-link\ member-port\ \(\d\+\/\S*\)$/virtual-chassis chassis-id 2 vf-link 0 member-port 2\/\1/gc
:%s/^multi-chassis\ chassis-group\ \(\d\+\)$/virtual-chassis chassis-id 2 chassis-group \1/gc

(The German word „Magie“ means „magic“.)

After you copied the lines and put them in the separate vcsetup.cfg's you can remove those rows from the configuration with the following command (removes both, multi-chassis and converted virtual-chassis commands)

:g/^\(multi\|virtual\)-chassis\ \(cha\|vf-\).*$/d

Remove the "linkagg range" from configuration

:g/^linkagg\ range.*$/d

Remove "multi-chassis active" from the link-aggregate configuration

:%s/\ multi-chassis\ active.*$//gc

Remove "system-id xx:xx:xx:xx:xx:xx"-rows from Link-Aggregation port/agg configuration

:g/^linkagg\ \(.*system-id\).*$/d

Convert Link-Aggregate configuration from "slot/port" to "chassis/slot/port"

Chassis 1:
:%s/^linkagg\ \(static\|lacp\)\ port\ \(\d\+\/\S*\)/linkagg \1 port 1\/\2/gc

Chassis 2:
:%s/^linkagg\ \(static\|lacp\)\ port\ \(\d\+\/\S*\)/linkagg \1 port 2\/\2/gc

Replace "multi-chassis vip-vlan" with standard "vlan"

:%s/^multi-chassis\ vip-vlan/vlan/gc

Convert VLAN port assignment from "slot/port" to "chassis/slot/port"

Chassis 1:
:%s/^vlan\ \(\d\+\)\ members\ port\ \(\d\+\/\S*\)/vlan \1 members port 1\/\2/gc

Chassis 2:
:%s/^vlan\ \(\d\+\)\ members\ port\ \(\d\+\/\S*\)/vlan \1 members port 2\/\2/gc

Automate the convertion of IP-Interfaces

After the migration from MC-LAG to Virtual-Chassis our servers/clients should be able to use the same gateway as before, hence we convert the IP-Interfaces to represent the „VIP-ADDRESS“ as new physical IP.

(If you don't want to do that automated convertion, but use e.g. VRRP you need to do this step manually.)

Chassis 1:
:%s/^ip\ interface\ \(\".*\"\)\ address \(\d\+\.\d\+\.\d\+\.\d\+\)\ mask\ \(\d\+\.\d\+\.\d\+\.\d\+\)\ vip-address\ \(\d\+\.\d\+\.\d\+\.\d\+\)/ip interface \1 address \4 mask \3/gc 

Chassis 2:
:g/^ip\ interface.*$/d

Convert LLDP configuration from "slot/port" to "chassis/slot/port"

Chassis 1:
:%s/^lldp\ \(nearest-bridge\|non-tpmr\|nearest-customer\)\ port \(\d\+\/\S*\)/lldp \1 port 1\/\2/gc 

Chassis 2:
:%s/^lldp\ \(nearest-bridge\|non-tpmr\|nearest-customer\)\ port \(\d\+\/\S*\)/lldp \1 port 2\/\2/gc

Remove unnecessary configuration/parameters

You should remove unnecessary configuratin/parameters from Chassis 2 as otherwise the merge of the two configuration is not straight forward:

:g/^system\ \(name\|contact\|location\)/d 
:g/^session\ prompt/d

Save the changes to both files and close them with VIM-command “:wq„.

Create the vcboot.cfg for Virtual Chassis

In the following you can see that we opened the primary configuration (chassis-1):

In the next step we open the configuration of the 2nd chassis and highlight the differences, so that we can easily copy them:

:vert diffsplit CORE02.cfg

You can jump between the windows with the VIM-command CTRL+WW. You can select rows visually with the VIM-command Shift+V (as seen in the screenshot) and cut the selected rows with „d“.

We'll paste the rows that you just cut (after changing focus to the „primary configuration“ with CTRL+WW) using the VIM-command „p“ at the desired position of the configuration. This step needs to be repeated for VLAN port assignment, link-aggregate port assignment, LLDP port configuration etc.

After you have merged all relevant configuration, you can save the configuration with the following VIM-command to „vcboot.cfg“:

:w vcboot.cfg

Example Configuration

MC-LAG Node 1 (CORE01)

CORE01.cfg

!========================================!
! File: /flash/working/boot.cfg !
!========================================!
! Chassis:
system name MC-Lag1
system contact myContact
system location "1. DC"
mac-retention admin-state enable
mac-retention dup-mac-trap admin-state enable
mac-retention timer 30
! Configuration:
! Capability Manager:
! Multi-Chassis:
multi-chassis chassis-id 1
multi-chassis vf-link create
multi-chassis vf-link member-port 1/1
multi-chassis vf-link member-port 1/20
multi-chassis chassis-group 9
! Virtual Chassis Manager:
! Virtual Flow Control:
! Interface:
! Link Aggregate:
linkagg range local 0-47 peer 48-95 multi-chassis 96-127
linkagg lacp agg 96 size 2 admin-state enable multi-chassis active
linkagg lacp agg 96 name "RACK01"
linkagg lacp agg 96 actor system-id 00:00:00:00:00:96
linkagg lacp agg 96 actor admin-key 96
linkagg lacp agg 97 size 2 admin-state enable multi-chassis active
linkagg lacp agg 97 name "RACK02"
linkagg lacp agg 97 actor system-id 00:00:00:00:00:97
linkagg lacp agg 97 actor admin-key 97
linkagg lacp agg 98 size 2 admin-state enable multi-chassis active
linkagg lacp agg 98 name "RACK03"
linkagg lacp agg 98 actor system-id 00:00:00:00:00:98
linkagg lacp agg 98 actor admin-key 98
linkagg lacp agg 99 size 2 admin-state enable multi-chassis active
linkagg lacp agg 99 name "RACK04"
linkagg lacp agg 99 actor system-id 00:00:00:00:00:99
linkagg lacp agg 99 actor admin-key 99
linkagg lacp agg 100 size 2 admin-state enable multi-chassis active
linkagg lacp agg 100 name "SW01"
linkagg lacp agg 100 actor system-id 00:00:00:00:01:00
linkagg lacp agg 100 actor admin-key 100
linkagg lacp agg 101 size 2 admin-state enable multi-chassis active
linkagg lacp agg 101 name "SW02"
linkagg lacp agg 101 actor system-id 00:00:00:00:01:01
linkagg lacp agg 101 actor admin-key 101
linkagg lacp agg 102 size 2 admin-state enable multi-chassis active
linkagg lacp agg 102 name "SW03"
linkagg lacp agg 102 actor system-id 00:00:00:00:01:02
linkagg lacp agg 102 actor admin-key 102
linkagg lacp agg 103 size 2 admin-state enable multi-chassis active
linkagg lacp agg 103 name "SW04"
linkagg lacp agg 103 actor system-id 00:00:00:00:01:03
linkagg lacp agg 103 actor admin-key 103
linkagg lacp agg 104 size 2 admin-state enable multi-chassis active
linkagg lacp agg 104 name "SW05"
linkagg lacp agg 104 actor system-id 00:00:00:00:01:04
linkagg lacp agg 104 actor admin-key 104
linkagg lacp agg 105 size 2 admin-state enable multi-chassis active
linkagg lacp agg 105 name "SW06"
linkagg lacp agg 105 actor system-id 00:00:00:00:01:05
linkagg lacp agg 105 actor admin-key 105
linkagg lacp agg 106 size 2 admin-state enable multi-chassis active
linkagg lacp agg 106 name "SW07"
linkagg lacp agg 106 actor system-id 00:00:00:00:01:06
linkagg lacp agg 106 actor admin-key 106
linkagg lacp port 1/2 actor admin-key 96
linkagg lacp port 1/2 actor system-id 00:00:00:00:00:96
linkagg lacp port 1/3 actor admin-key 97
linkagg lacp port 1/3 actor system-id 00:00:00:00:00:97
linkagg lacp port 1/4 actor admin-key 98
linkagg lacp port 1/4 actor system-id 00:00:00:00:00:98
linkagg lacp port 1/5 actor admin-key 99
linkagg lacp port 1/5 actor system-id 00:00:00:00:00:99
linkagg lacp port 1/6 actor admin-key 100
linkagg lacp port 1/6 actor system-id 00:00:00:00:01:00
linkagg lacp port 1/7 actor admin-key 101
linkagg lacp port 1/7 actor system-id 00:00:00:00:01:01
linkagg lacp port 1/8 actor admin-key 102
linkagg lacp port 1/8 actor system-id 00:00:00:00:01:02
linkagg lacp port 1/9 actor admin-key 103
linkagg lacp port 1/9 actor system-id 00:00:00:00:01:03
linkagg lacp port 1/10 actor admin-key 104
linkagg lacp port 1/10 actor system-id 00:00:00:00:01:04
linkagg lacp port 1/11 actor admin-key 105
linkagg lacp port 1/11 actor system-id 00:00:00:00:01:05
linkagg lacp port 1/12 actor admin-key 106
linkagg lacp port 1/12 actor system-id 00:00:00:00:01:06
! VLAN:
vlan 1 admin-state enable
vlan 1 name "Mgmt"
multi-chassis vip-vlan 100 admin-state enable
multi-chassis vip-vlan 100 name "Server"
vlan 102-104 admin-state enable
vlan 102 name "Guest"
vlan 103 name "VoIP"
vlan 104 name "Build"
vlan 106 admin-state enable
vlan 106 name "Dev"
multi-chassis vip-vlan 110-113 admin-state enable
multi-chassis vip-vlan 110 name "Client1"
multi-chassis vip-vlan 111 name "Client2"
multi-chassis vip-vlan 112 name "Client3"
multi-chassis vip-vlan 113 name "Client4"
multi-chassis vip-vlan 150 admin-state enable
multi-chassis vip-vlan 150 name "VIP VLAN"
vlan 100 members linkagg 96-99 tagged
vlan 102 members linkagg 100-106 tagged
vlan 103 members linkagg 96-106 tagged
vlan 104 members linkagg 96-106 tagged
vlan 106 members linkagg 96-106 tagged
vlan 110 members linkagg 100-101 tagged
vlan 111 members linkagg 102-103 tagged
vlan 112 members linkagg 104-105 tagged
vlan 113 members linkagg 106 tagged
vlan 150 members linkagg 96-99 tagged
! Spanning Tree:
spantree vlan 1 admin-state enable
spantree vlan 100 admin-state enable
spantree vlan 102 admin-state enable
spantree vlan 103 admin-state enable
spantree vlan 104 admin-state enable
spantree vlan 106 admin-state enable
spantree vlan 110 admin-state enable
spantree vlan 111 admin-state enable
spantree vlan 112 admin-state enable
spantree vlan 113 admin-state enable
spantree vlan 150 admin-state enable
! Bridging:
! Port Mirroring:
! Port Mapping:
! IP:
ip service port 21 admin-state enable
ip service port 22 admin-state enable
ip service port 23 admin-state enable
ip service port 80 admin-state enable
ip service port 123 admin-state enable
ip service port 443 admin-state enable
ip interface "Mgmt" address 192.168.130.197 mask 255.255.255.0 vlan 1 no forward ifindex 1
ip interface "Client1" address 10.2.140.197 mask 255.255.255.0 vip-address 10.2.140.1 vlan 110 ifindex 2
ip interface "Client2" address 10.2.141.197 mask 255.255.255.0 vip-address 10.2.141.1 vlan 111 ifindex 3
ip interface "Client3" address 10.2.142.197 mask 255.255.255.0 vip-address 10.2.142.1 vlan 112 ifindex 4
ip interface "Client4" address 10.2.143.197 mask 255.255.255.0 vip-address 10.2.143.1 vlan 113 ifindex 5
ip interface "Server" address 10.2.128.197 mask 255.255.255.0 vip-address 10.2.128.1 vlan 100 ifindex 6
ip interface "Transfer_Firewall" address 192.168.150.197 mask 255.255.255.0 vip-address 192.168.150.1 vlan 150 ifindex 7
! IPv6:
! IPSec:
! IPMS:
! AAA:
aaa authentication console "local"
aaa authentication ftp "local"
aaa authentication http "local"
aaa authentication snmp "local"
aaa authentication ssh "local"
user password-size min 6
! NTP:
ntp server 192.168.2.253
ntp client admin-state enable
! QOS:
policy condition from_voip source vlan 103
policy action set_dscp dscp 46
policy rule prio_voip condition from_voip action set_dscp
qos apply
! Policy Manager:
! VLAN Stacking:
! ERP:
! MVRP:
! LLDP:
lldp nearest-bridge port 1/1-20 tlv management system-capabilities enable
lldp nearest-bridge port 1/1-20 tlv management system-description enable
lldp nearest-bridge port 1/1-20 tlv management system-name enable
lldp nearest-bridge port 1/1-20 tlv management port-description enable
lldp non-tpmr port 1/1-20 tlv management system-capabilities enable
lldp non-tpmr port 1/1-20 tlv management system-description enable
lldp non-tpmr port 1/1-20 tlv management system-name enable
lldp non-tpmr port 1/1-20 tlv management port-description enable
lldp nearest-customer port 1/1-20 tlv management system-capabilities enable
lldp nearest-customer port 1/1-20 tlv management system-description enable
lldp nearest-customer port 1/1-20 tlv management system-name enable
lldp nearest-customer port 1/1-20 tlv management port-description enable
lldp nearest-bridge port 1/1-20 tlv management management-address enable
lldp non-tpmr port 1/1-20 tlv management management-address enable
lldp nearest-customer port 1/1-20 tlv management management-address enable
! UDLD:
! Server Load Balance:
! High Availability Vlan:
! Session Manager:
session cli timeout 30
session http timeout 30
session prompt default "CORE01 ->"
command-log enable
! Web:
! Trap Manager:
snmp station 192.168.2.203 162 "snmpv3" v3 enable
! Health Monitor:
! System Service:
swlog output socket 192.168.2.203
system timezone CET
! SNMP:
snmp security authentication set
snmp community-map mode enable
snmp community-map "public" user "snmp" enable
! BFD:
! IP Route Manager:
ip static-route 0.0.0.0/0 gateway 192.168.150.253 metric 1
! VRRP:
! UDP Relay:
! RIP:
! OSPF:
! ISIS:
! IP Multicast:
! DVMRP:
! IPMR:
! RIPng:
! OSPF3:
! BGP:
! Netsec:
! Module:
! RDP:
! DA-UNP:
! DHL:
! Ethernet-OAM:
! SAA:
! SPB-ISIS:
! SVCMGR:
! LDP:
! EVB:

Modified configuration of MC-LAG Node 1 (CORE01)

modified-CORE01.cfg

!========================================!
! File: /flash/working/boot.cfg !
!========================================!
! Chassis:
system name MC-Lag1
system contact myContact
system location "1. DC"
mac-retention admin-state enable
mac-retention dup-mac-trap admin-state enable
mac-retention timer 30
! Configuration:
! Capability Manager:
! Multi-Chassis:
! Virtual Chassis Manager:
! Virtual Flow Control:
! Interface:
! Link Aggregate:
linkagg lacp agg 96 size 2 admin-state enable
linkagg lacp agg 96 name "RACK01"
linkagg lacp agg 96 actor admin-key 96
linkagg lacp agg 97 size 2 admin-state enable
linkagg lacp agg 97 name "RACK02"
linkagg lacp agg 97 actor admin-key 97
linkagg lacp agg 98 size 2 admin-state enable
linkagg lacp agg 98 name "RACK03"
linkagg lacp agg 98 actor admin-key 98
linkagg lacp agg 99 size 2 admin-state enable
linkagg lacp agg 99 name "RACK04"
linkagg lacp agg 99 actor admin-key 99
linkagg lacp agg 100 size 2 admin-state enable
linkagg lacp agg 100 name "SW01"
linkagg lacp agg 100 actor admin-key 100
linkagg lacp agg 101 size 2 admin-state enable
linkagg lacp agg 101 name "SW02"
linkagg lacp agg 101 actor admin-key 101
linkagg lacp agg 102 size 2 admin-state enable
linkagg lacp agg 102 name "SW03"
linkagg lacp agg 102 actor admin-key 102
linkagg lacp agg 103 size 2 admin-state enable
linkagg lacp agg 103 name "SW04"
linkagg lacp agg 103 actor admin-key 103
linkagg lacp agg 104 size 2 admin-state enable
linkagg lacp agg 104 name "SW05"
linkagg lacp agg 104 actor admin-key 104
linkagg lacp agg 105 size 2 admin-state enable
linkagg lacp agg 105 name "SW06"
linkagg lacp agg 105 actor admin-key 105
linkagg lacp agg 106 size 2 admin-state enable
linkagg lacp agg 106 name "SW07"
linkagg lacp agg 106 actor admin-key 106
linkagg lacp port 1/1/2 actor admin-key 96
linkagg lacp port 1/1/3 actor admin-key 97
linkagg lacp port 1/1/4 actor admin-key 98
linkagg lacp port 1/1/5 actor admin-key 99
linkagg lacp port 1/1/6 actor admin-key 100
linkagg lacp port 1/1/7 actor admin-key 101
linkagg lacp port 1/1/8 actor admin-key 102
linkagg lacp port 1/1/9 actor admin-key 103
linkagg lacp port 1/1/10 actor admin-key 104
linkagg lacp port 1/1/11 actor admin-key 105
linkagg lacp port 1/1/12 actor admin-key 106
! VLAN:
vlan 1 admin-state enable
vlan 1 name "Mgmt"
vlan 100 admin-state enable
vlan 100 name "Server"
vlan 102-104 admin-state enable
vlan 102 name "Guest"
vlan 103 name "VoIP"
vlan 104 name "Build"
vlan 106 admin-state enable
vlan 106 name "Dev"
vlan 110-113 admin-state enable
vlan 110 name "Client1"
vlan 111 name "Client2"
vlan 112 name "Client3"
vlan 113 name "Client4"
vlan 150 admin-state enable
vlan 150 name "VIP VLAN"
vlan 100 members linkagg 96-99 tagged
vlan 102 members linkagg 100-106 tagged
vlan 103 members linkagg 96-106 tagged
vlan 104 members linkagg 96-106 tagged
vlan 106 members linkagg 96-106 tagged
vlan 110 members linkagg 100-101 tagged
vlan 111 members linkagg 102-103 tagged
vlan 112 members linkagg 104-105 tagged
vlan 113 members linkagg 106 tagged
vlan 150 members linkagg 96-99 tagged
! Spanning Tree:
spantree vlan 1 admin-state enable
spantree vlan 100 admin-state enable
spantree vlan 102 admin-state enable
spantree vlan 103 admin-state enable
spantree vlan 104 admin-state enable
spantree vlan 106 admin-state enable
spantree vlan 110 admin-state enable
spantree vlan 111 admin-state enable
spantree vlan 112 admin-state enable
spantree vlan 113 admin-state enable
spantree vlan 150 admin-state enable
! Bridging:
! Port Mirroring:
! Port Mapping:
! IP:
ip service port 21 admin-state enable
ip service port 22 admin-state enable
ip service port 23 admin-state enable
ip service port 80 admin-state enable
ip service port 123 admin-state enable
ip service port 443 admin-state enable
ip interface "Mgmt" address 192.168.130.197 mask 255.255.255.0 vlan 1 no forward ifindex 1
ip interface "Client1" address 10.2.140.1 mask 255.255.255.0 vlan 110 ifindex 2
ip interface "Client2" address 10.2.141.1 mask 255.255.255.0 vlan 111 ifindex 3
ip interface "Client3" address 10.2.142.1 mask 255.255.255.0 vlan 112 ifindex 4
ip interface "Client4" address 10.2.143.1 mask 255.255.255.0 vlan 113 ifindex 5
ip interface "Server" address 10.2.128.1 mask 255.255.255.0 vlan 100 ifindex 6
ip interface "Transfer_Firewall" address 192.168.150.1 mask 255.255.255.0 vlan 150 ifindex 7
! IPv6:
! IPSec:
! IPMS:
! AAA:
aaa authentication console "local"
aaa authentication ftp "local"
aaa authentication http "local"
aaa authentication snmp "local"
aaa authentication ssh "local"
user password-size min 6
! NTP:
ntp server 192.168.2.253
ntp client admin-state enable
! QOS:
policy condition from_voip source vlan 103
policy action set_dscp dscp 46
policy rule prio_voip condition from_voip action set_dscp
qos apply
! Policy Manager:
! VLAN Stacking:
! ERP:
! MVRP:
! LLDP:
lldp nearest-bridge port 1/1/1-20 tlv management system-capabilities enable
lldp nearest-bridge port 1/1/1-20 tlv management system-description enable
lldp nearest-bridge port 1/1/1-20 tlv management system-name enable
lldp nearest-bridge port 1/1/1-20 tlv management port-description enable
lldp non-tpmr port 1/1/1-20 tlv management system-capabilities enable
lldp non-tpmr port 1/1/1-20 tlv management system-description enable
lldp non-tpmr port 1/1/1-20 tlv management system-name enable
lldp non-tpmr port 1/1/1-20 tlv management port-description enable
lldp nearest-customer port 1/1/1-20 tlv management system-capabilities enable
lldp nearest-customer port 1/1/1-20 tlv management system-description enable
lldp nearest-customer port 1/1/1-20 tlv management system-name enable
lldp nearest-customer port 1/1/1-20 tlv management port-description enable
lldp nearest-bridge port 1/1/1-20 tlv management management-address enable
lldp non-tpmr port 1/1/1-20 tlv management management-address enable
lldp nearest-customer port 1/1/1-20 tlv management management-address enable
! UDLD:
! Server Load Balance:
! High Availability Vlan:
! Session Manager:
session cli timeout 30
session http timeout 30
session prompt default "CORE01 ->"
command-log enable
! Web:
! Trap Manager:
snmp station 192.168.2.203 162 "snmpv3" v3 enable
! Health Monitor:
! System Service:
swlog output socket 192.168.2.203
system timezone CET
! SNMP:
snmp security authentication set
snmp community-map mode enable
snmp community-map "public" user "snmp" enable
! BFD:
! IP Route Manager:
ip static-route 0.0.0.0/0 gateway 192.168.150.253 metric 1
! VRRP:
! UDP Relay:
! RIP:
! OSPF:
! ISIS:
! IP Multicast:
! DVMRP:
! IPMR:
! RIPng:
! OSPF3:
! BGP:
! Netsec:
! Module:
! RDP:
! DA-UNP:
! DHL:
! Ethernet-OAM:
! SAA:
! SPB-ISIS:
! SVCMGR:
! LDP:
! EVB:

MC-LAG Node 2 (CORE02)

CORE02.cfg

!========================================!
! File: /flash/working/boot.cfg !
!========================================!
! Chassis:
system name MC-Lag2
system contact myContact
system location "1. DC"
mac-retention admin-state enable
mac-retention dup-mac-trap admin-state enable
mac-retention timer 30
! Configuration:
! Capability Manager:
! Multi-Chassis:
multi-chassis chassis-id 2
multi-chassis vf-link create
multi-chassis vf-link member-port 1/1
multi-chassis vf-link member-port 1/20
multi-chassis chassis-group 9
! Virtual Chassis Manager:
! Virtual Flow Control:
! Interface:
! Link Aggregate:
linkagg range local 48-95 peer 0-47 multi-chassis 96-127
linkagg lacp agg 96 size 2 admin-state enable multi-chassis active
linkagg lacp agg 96 name "RACK01"
linkagg lacp agg 96 actor system-id 00:00:00:00:00:96
linkagg lacp agg 96 actor admin-key 96
linkagg lacp agg 97 size 2 admin-state enable multi-chassis active
linkagg lacp agg 97 name "RACK02"
linkagg lacp agg 97 actor system-id 00:00:00:00:00:97
linkagg lacp agg 97 actor admin-key 97
linkagg lacp agg 98 size 2 admin-state enable multi-chassis active
linkagg lacp agg 98 name "RACK03"
linkagg lacp agg 98 actor system-id 00:00:00:00:00:98
linkagg lacp agg 98 actor admin-key 98
linkagg lacp agg 99 size 2 admin-state enable multi-chassis active
linkagg lacp agg 99 name "RACK04"
linkagg lacp agg 99 actor system-id 00:00:00:00:00:99
linkagg lacp agg 99 actor admin-key 99
linkagg lacp agg 100 size 2 admin-state enable multi-chassis active
linkagg lacp agg 100 name "SW01"
linkagg lacp agg 100 actor system-id 00:00:00:00:01:00
linkagg lacp agg 100 actor admin-key 100
linkagg lacp agg 101 size 2 admin-state enable multi-chassis active
linkagg lacp agg 101 name "SW02"
linkagg lacp agg 101 actor system-id 00:00:00:00:01:01
linkagg lacp agg 101 actor admin-key 101
linkagg lacp agg 102 size 2 admin-state enable multi-chassis active
linkagg lacp agg 102 name "SW03"
linkagg lacp agg 102 actor system-id 00:00:00:00:01:02
linkagg lacp agg 102 actor admin-key 102
linkagg lacp agg 103 size 2 admin-state enable multi-chassis active
linkagg lacp agg 103 name "SW04"
linkagg lacp agg 103 actor system-id 00:00:00:00:01:03
linkagg lacp agg 103 actor admin-key 103
linkagg lacp agg 104 size 2 admin-state enable multi-chassis active
linkagg lacp agg 104 name "SW05"
linkagg lacp agg 104 actor system-id 00:00:00:00:01:04
linkagg lacp agg 104 actor admin-key 104
linkagg lacp agg 105 size 2 admin-state enable multi-chassis active
linkagg lacp agg 105 name "SW06"
linkagg lacp agg 105 actor system-id 00:00:00:00:01:05
linkagg lacp agg 105 actor admin-key 105
linkagg lacp agg 106 size 2 admin-state enable multi-chassis active
linkagg lacp agg 106 name "SW07"
linkagg lacp agg 106 actor system-id 00:00:00:00:01:06
linkagg lacp agg 106 actor admin-key 106
linkagg lacp port 1/2 actor admin-key 96
linkagg lacp port 1/2 actor system-id 00:00:00:00:00:96
linkagg lacp port 1/3 actor admin-key 97
linkagg lacp port 1/3 actor system-id 00:00:00:00:00:97
linkagg lacp port 1/4 actor admin-key 98
linkagg lacp port 1/4 actor system-id 00:00:00:00:00:98
linkagg lacp port 1/5 actor admin-key 99
linkagg lacp port 1/5 actor system-id 00:00:00:00:00:99
linkagg lacp port 1/6 actor admin-key 100
linkagg lacp port 1/6 actor system-id 00:00:00:00:01:00
linkagg lacp port 1/7 actor admin-key 101
linkagg lacp port 1/7 actor system-id 00:00:00:00:01:01
linkagg lacp port 1/8 actor admin-key 102
linkagg lacp port 1/8 actor system-id 00:00:00:00:01:02
linkagg lacp port 1/9 actor admin-key 103
linkagg lacp port 1/9 actor system-id 00:00:00:00:01:03
linkagg lacp port 1/10 actor admin-key 104
linkagg lacp port 1/10 actor system-id 00:00:00:00:01:04
linkagg lacp port 1/11 actor admin-key 105
linkagg lacp port 1/11 actor system-id 00:00:00:00:01:05
linkagg lacp port 1/12 actor admin-key 106
linkagg lacp port 1/12 actor system-id 00:00:00:00:01:06
! VLAN:
vlan 1 admin-state enable
vlan 1 name "Mgmt"
multi-chassis vip-vlan 100 admin-state enable
multi-chassis vip-vlan 100 name "Server"
vlan 102-104 admin-state enable
vlan 102 name "Guest"
vlan 103 name "VoIP"
vlan 104 name "Build"
vlan 106 admin-state enable
vlan 106 name "Dev"
multi-chassis vip-vlan 110-113 admin-state enable
multi-chassis vip-vlan 110 name "Client1"
multi-chassis vip-vlan 111 name "Client2"
multi-chassis vip-vlan 112 name "Client3"
multi-chassis vip-vlan 113 name "Client4"
multi-chassis vip-vlan 150 admin-state enable
multi-chassis vip-vlan 150 name "VIP VLAN"
vlan 100 members linkagg 96-99 tagged
vlan 102 members linkagg 100-106 tagged
vlan 103 members linkagg 96-106 tagged
vlan 104 members linkagg 96-106 tagged
vlan 106 members linkagg 96-106 tagged
vlan 110 members linkagg 100-101 tagged
vlan 111 members linkagg 102-103 tagged
vlan 112 members linkagg 104-105 tagged
vlan 113 members linkagg 106 tagged
vlan 150 members linkagg 96-99 tagged
! Spanning Tree:
spantree vlan 1 admin-state enable
spantree vlan 100 admin-state enable
spantree vlan 102 admin-state enable
spantree vlan 103 admin-state enable
spantree vlan 104 admin-state enable
spantree vlan 106 admin-state enable
spantree vlan 110 admin-state enable
spantree vlan 111 admin-state enable
spantree vlan 112 admin-state enable
spantree vlan 113 admin-state enable
spantree vlan 150 admin-state enable
! Bridging:
! Port Mirroring:
! Port Mapping:
! IP:
ip service port 21 admin-state enable
ip service port 22 admin-state enable
ip service port 23 admin-state enable
ip service port 80 admin-state enable
ip service port 123 admin-state enable
ip service port 443 admin-state enable
ip interface "Mgmt" address 192.168.130.198 mask 255.255.255.0 vlan 1 no forward ifindex 1
ip interface "Client1" address 10.2.140.198 mask 255.255.255.0 vip-address 10.2.140.1 vlan 110 ifindex 2
ip interface "Client2" address 10.2.141.198 mask 255.255.255.0 vip-address 10.2.141.1 vlan 111 ifindex 3
ip interface "Client3" address 10.2.142.198 mask 255.255.255.0 vip-address 10.2.142.1 vlan 112 ifindex 4
ip interface "Client4" address 10.2.143.198 mask 255.255.255.0 vip-address 10.2.143.1 vlan 113 ifindex 5
ip interface "Server" address 10.2.128.198 mask 255.255.255.0 vip-address 10.2.128.1 vlan 100 ifindex 6
ip interface "Transfer_Firewall" address 192.168.150.198 mask 255.255.255.0 vip-address 192.168.150.1 vlan 150 ifindex 7
! IPv6:
! IPSec:
! IPMS:
! AAA:
aaa authentication console "local"
aaa authentication ftp "local"
aaa authentication http "local"
aaa authentication snmp "local"
aaa authentication ssh "local"
user password-size min 6
! NTP:
ntp server 192.168.2.253
ntp client admin-state enable
! QOS:
policy condition from_voip source vlan 103
policy action set_dscp dscp 46
policy rule prio_voip condition from_voip action set_dscp
qos apply
! Policy Manager:
! VLAN Stacking:
! ERP:
! MVRP:
! LLDP:
lldp nearest-bridge port 1/1-20 tlv management system-capabilities enable
lldp nearest-bridge port 1/1-20 tlv management system-description enable
lldp nearest-bridge port 1/1-20 tlv management system-name enable
lldp nearest-bridge port 1/1-20 tlv management port-description enable
lldp non-tpmr port 1/1-20 tlv management system-capabilities enable
lldp non-tpmr port 1/1-20 tlv management system-description enable
lldp non-tpmr port 1/1-20 tlv management system-name enable
lldp non-tpmr port 1/1-20 tlv management port-description enable
lldp nearest-customer port 1/1-20 tlv management system-capabilities enable
lldp nearest-customer port 1/1-20 tlv management system-description enable
lldp nearest-customer port 1/1-20 tlv management system-name enable
lldp nearest-customer port 1/1-20 tlv management port-description enable
lldp nearest-bridge port 1/1-20 tlv management management-address enable
lldp non-tpmr port 1/1-20 tlv management management-address enable
lldp nearest-customer port 1/1-20 tlv management management-address enable
! UDLD:
! Server Load Balance:
! High Availability Vlan:
! Session Manager:
session cli timeout 30
session http timeout 30
session prompt default "CORE02 ->"
command-log enable
! Web:
! Trap Manager:
snmp station 192.168.2.203 162 "snmpv3" v3 enable
! Health Monitor:
! System Service:
swlog output socket 192.168.2.203
system timezone CET
! SNMP:
snmp security authentication set
snmp community-map mode enable
snmp community-map "public" user "snmp" enable
! BFD:
! IP Route Manager:
ip static-route 0.0.0.0/0 gateway 192.168.150.253 metric 1
! VRRP:
! UDP Relay:
! RIP:
! OSPF:
! ISIS:
! IP Multicast:
! DVMRP:
! IPMR:
! RIPng:
! OSPF3:
! BGP:
! Netsec:
! Module:
! RDP:
! DA-UNP:
! DHL:
! Ethernet-OAM:
! SAA:
! SPB-ISIS:
! SVCMGR:
! LDP:
! EVB:

Modified configuration of MC-LAG Node 2 (CORE02)

modified-CORE02.cfg

!========================================!
! File: /flash/working/boot.cfg          !
!========================================!
! Chassis:
mac-retention admin-state enable
mac-retention dup-mac-trap admin-state enable
mac-retention timer 30
 
! Configuration:
 
! Capability Manager:
! Multi-Chassis:
 
! Virtual Chassis Manager:
! Virtual Flow Control:
! Interface:
! Link Aggregate:
linkagg lacp agg 96 size 2 admin-state enable
linkagg lacp agg 96 name "RACK01"
linkagg lacp agg 96 actor admin-key 96
linkagg lacp agg 97 size 2 admin-state enable
linkagg lacp agg 97 name "RACK02"
linkagg lacp agg 97 actor admin-key 97
linkagg lacp agg 98 size 2 admin-state enable
linkagg lacp agg 98 name "RACK03"
linkagg lacp agg 98 actor admin-key 98
linkagg lacp agg 99 size 2 admin-state enable
linkagg lacp agg 99 name "RACK04"
linkagg lacp agg 99 actor admin-key 99
linkagg lacp agg 100 size 2 admin-state enable
linkagg lacp agg 100 name "SW01"
linkagg lacp agg 100 actor admin-key 100
linkagg lacp agg 101 size 2 admin-state enable
linkagg lacp agg 101 name "SW02"
linkagg lacp agg 101 actor admin-key 101
linkagg lacp agg 102 size 2 admin-state enable
linkagg lacp agg 102 name "SW03"
linkagg lacp agg 102 actor admin-key 102
linkagg lacp agg 103 size 2 admin-state enable
linkagg lacp agg 103 name "SW04"
linkagg lacp agg 103 actor admin-key 103
linkagg lacp agg 104 size 2 admin-state enable
linkagg lacp agg 104 name "SW05"
linkagg lacp agg 104 actor admin-key 104
linkagg lacp agg 105 size 2 admin-state enable
linkagg lacp agg 105 name "SW06"
linkagg lacp agg 105 actor admin-key 105
linkagg lacp agg 106 size 2 admin-state enable
linkagg lacp agg 106 name "SW07"
linkagg lacp agg 106 actor admin-key 106
linkagg lacp port 2/1/2 actor admin-key 96
linkagg lacp port 2/1/3 actor admin-key 97
linkagg lacp port 2/1/4 actor admin-key 98
linkagg lacp port 2/1/5 actor admin-key 99
linkagg lacp port 2/1/6 actor admin-key 100
linkagg lacp port 2/1/7 actor admin-key 101
linkagg lacp port 2/1/8 actor admin-key 102
linkagg lacp port 2/1/9 actor admin-key 103
linkagg lacp port 2/1/10 actor admin-key 104
linkagg lacp port 2/1/11 actor admin-key 105
linkagg lacp port 2/1/12 actor admin-key 106
 
! VLAN:
vlan 1 admin-state enable
vlan 1 name "Mgmt"
vlan 100 admin-state enable
vlan 100 name "Server"
vlan 102-104 admin-state enable
vlan 102 name "Guest"
vlan 103 name "VoIP"
vlan 104 name "Build"
vlan 106 admin-state enable
vlan 106 name "Dev"
vlan 110-113 admin-state enable
vlan 110 name "Client1"
vlan 111 name "Client2"
vlan 112 name "Client3"
vlan 113 name "Client4"
vlan 150 admin-state enable
vlan 150 name "VIP VLAN"
vlan 100 members linkagg 96-99 tagged
vlan 102 members linkagg 100-106 tagged
vlan 103 members linkagg 96-106 tagged
vlan 104 members linkagg 96-106 tagged
vlan 106 members linkagg 96-106 tagged
vlan 110 members linkagg 100-101 tagged
vlan 111 members linkagg 102-103 tagged
vlan 112 members linkagg 104-105 tagged
vlan 113 members linkagg 106 tagged
vlan 150 members linkagg 96-99 tagged
 
! Spanning Tree:
spantree vlan 1 admin-state enable 
spantree vlan 100 admin-state enable 
spantree vlan 102 admin-state enable 
spantree vlan 103 admin-state enable 
spantree vlan 104 admin-state enable 
spantree vlan 106 admin-state enable 
spantree vlan 110 admin-state enable 
spantree vlan 111 admin-state enable 
spantree vlan 112 admin-state enable 
spantree vlan 113 admin-state enable 
spantree vlan 150 admin-state enable 
 
! Bridging:
! Port Mirroring:
! Port Mapping:
! IP:
ip service port 21 admin-state enable
ip service port 22 admin-state enable
ip service port 23 admin-state enable
ip service port 80 admin-state enable
ip service port 123 admin-state enable
ip service port 443 admin-state enable
 
! IPv6:
! IPSec:
! IPMS:
! AAA:
aaa authentication console "local" 
aaa authentication ftp "local" 
aaa authentication http "local" 
aaa authentication snmp "local" 
aaa authentication ssh "local" 
 
user password-size min 6
 
! NTP:
ntp server 192.168.2.253
ntp client admin-state enable
 
! QOS:
policy condition from_voip source vlan 103 
policy action set_dscp dscp 46 
policy rule prio_voip condition from_voip action set_dscp 
qos apply
 
! Policy Manager:
! VLAN Stacking:
! ERP:
! MVRP:
! LLDP:
lldp nearest-bridge port 2/1/1-20 tlv management system-capabilities enable
lldp nearest-bridge port 2/1/1-20 tlv management system-description enable
lldp nearest-bridge port 2/1/1-20 tlv management system-name enable
lldp nearest-bridge port 2/1/1-20 tlv management port-description enable
lldp non-tpmr port 2/1/1-20 tlv management system-capabilities enable
lldp non-tpmr port 2/1/1-20 tlv management system-description enable
lldp non-tpmr port 2/1/1-20 tlv management system-name enable
lldp non-tpmr port 2/1/1-20 tlv management port-description enable
lldp nearest-customer port 2/1/1-20 tlv management system-capabilities enable
lldp nearest-customer port 2/1/1-20 tlv management system-description enable
lldp nearest-customer port 2/1/1-20 tlv management system-name enable
lldp nearest-customer port 2/1/1-20 tlv management port-description enable
lldp nearest-bridge port 2/1/1-20 tlv management management-address enable
lldp non-tpmr port 2/1/1-20 tlv management management-address enable
lldp nearest-customer port 2/1/1-20 tlv management management-address enable
 
! UDLD:
! Server Load Balance:
! High Availability Vlan:
! Session Manager:
session cli timeout 30
session http timeout 30
command-log enable
 
! Web:
! Trap Manager:
snmp station 192.168.2.203 162 "snmpv3" v3 enable
 
! Health Monitor:
! System Service:
swlog output socket 192.168.2.203
system timezone CET
 
! SNMP:
snmp security authentication set
snmp community-map mode enable
snmp community-map "public" user "snmp" enable
 
! BFD:
! IP Route Manager:
ip static-route 0.0.0.0/0 gateway 192.168.150.253 metric 1
 
! VRRP:
! UDP Relay:
! RIP:
! OSPF:
! ISIS:
! IP Multicast:
! DVMRP:
! IPMR:
! RIPng:
! OSPF3:
! BGP:
! Netsec:
! Module:
! RDP:
! DA-UNP:
! DHL:
! Ethernet-OAM:
! SAA:
! SPB-ISIS:
! SVCMGR:
! LDP:
! EVB:

Final configuration (VC-CORE01, vcboot.cfg)

vcboot.cfg

!========================================!
! File: /flash/working/boot.cfg !
!========================================!
! Chassis:
system name MC-Lag1
system contact myContact
system location "1. DC"
mac-retention admin-state enable
mac-retention dup-mac-trap admin-state enable
mac-retention timer 30
! Configuration:
! Capability Manager:
! Multi-Chassis:
! Virtual Chassis Manager:
! Virtual Flow Control:
! Interface:
! Link Aggregate:
linkagg lacp agg 96 size 2 admin-state enable
linkagg lacp agg 96 name "RACK01"
linkagg lacp agg 96 actor admin-key 96
linkagg lacp agg 97 size 2 admin-state enable
linkagg lacp agg 97 name "RACK02"
linkagg lacp agg 97 actor admin-key 97
linkagg lacp agg 98 size 2 admin-state enable
linkagg lacp agg 98 name "RACK03"
linkagg lacp agg 98 actor admin-key 98
linkagg lacp agg 99 size 2 admin-state enable
linkagg lacp agg 99 name "RACK04"
linkagg lacp agg 99 actor admin-key 99
linkagg lacp agg 100 size 2 admin-state enable
linkagg lacp agg 100 name "SW01"
linkagg lacp agg 100 actor admin-key 100
linkagg lacp agg 101 size 2 admin-state enable
linkagg lacp agg 101 name "SW02"
linkagg lacp agg 101 actor admin-key 101
linkagg lacp agg 102 size 2 admin-state enable
linkagg lacp agg 102 name "SW03"
linkagg lacp agg 102 actor admin-key 102
linkagg lacp agg 103 size 2 admin-state enable
linkagg lacp agg 103 name "SW04"
linkagg lacp agg 103 actor admin-key 103
linkagg lacp agg 104 size 2 admin-state enable
linkagg lacp agg 104 name "SW05"
linkagg lacp agg 104 actor admin-key 104
linkagg lacp agg 105 size 2 admin-state enable
linkagg lacp agg 105 name "SW06"
linkagg lacp agg 105 actor admin-key 105
linkagg lacp agg 106 size 2 admin-state enable
linkagg lacp agg 106 name "SW07"
linkagg lacp agg 106 actor admin-key 106
linkagg lacp port 1/1/2 actor admin-key 96
linkagg lacp port 1/1/3 actor admin-key 97
linkagg lacp port 1/1/4 actor admin-key 98
linkagg lacp port 1/1/5 actor admin-key 99
linkagg lacp port 1/1/6 actor admin-key 100
linkagg lacp port 1/1/7 actor admin-key 101
linkagg lacp port 1/1/8 actor admin-key 102
linkagg lacp port 1/1/9 actor admin-key 103
linkagg lacp port 1/1/10 actor admin-key 104
linkagg lacp port 1/1/11 actor admin-key 105
linkagg lacp port 1/1/12 actor admin-key 106
linkagg lacp port 2/1/2 actor admin-key 96
linkagg lacp port 2/1/3 actor admin-key 97
linkagg lacp port 2/1/4 actor admin-key 98
linkagg lacp port 2/1/5 actor admin-key 99
linkagg lacp port 2/1/6 actor admin-key 100
linkagg lacp port 2/1/7 actor admin-key 101
linkagg lacp port 2/1/8 actor admin-key 102
linkagg lacp port 2/1/9 actor admin-key 103
linkagg lacp port 2/1/10 actor admin-key 104
linkagg lacp port 2/1/11 actor admin-key 105
linkagg lacp port 2/1/12 actor admin-key 106
! VLAN:
vlan 1 admin-state enable
vlan 1 name "Mgmt"
vlan 100 admin-state enable
vlan 100 name "Server"
vlan 102-104 admin-state enable
vlan 102 name "Guest"
vlan 103 name "VoIP"
vlan 104 name "Build"
vlan 106 admin-state enable
vlan 106 name "Dev"
vlan 110-113 admin-state enable
vlan 110 name "Client1"
vlan 111 name "Client2"
vlan 112 name "Client3"
vlan 113 name "Client4"
vlan 150 admin-state enable
vlan 150 name "VIP VLAN"
vlan 100 members linkagg 96-99 tagged
vlan 102 members linkagg 100-106 tagged
vlan 103 members linkagg 96-106 tagged
vlan 104 members linkagg 96-106 tagged
vlan 106 members linkagg 96-106 tagged
vlan 110 members linkagg 100-101 tagged
vlan 111 members linkagg 102-103 tagged
vlan 112 members linkagg 104-105 tagged
vlan 113 members linkagg 106 tagged
vlan 150 members linkagg 96-99 tagged
! Spanning Tree:
spantree vlan 1 admin-state enable
spantree vlan 100 admin-state enable
spantree vlan 102 admin-state enable
spantree vlan 103 admin-state enable
spantree vlan 104 admin-state enable
spantree vlan 106 admin-state enable
spantree vlan 110 admin-state enable
spantree vlan 111 admin-state enable
spantree vlan 112 admin-state enable
spantree vlan 113 admin-state enable
spantree vlan 150 admin-state enable
! Bridging:
! Port Mirroring:
! Port Mapping:
! IP:
ip service port 21 admin-state enable
ip service port 22 admin-state enable
ip service port 23 admin-state enable
ip service port 80 admin-state enable
ip service port 123 admin-state enable
ip service port 443 admin-state enable
ip interface "Mgmt" address 192.168.130.197 mask 255.255.255.0 vlan 1 no forward ifindex 1
ip interface "Client1" address 10.2.140.1 mask 255.255.255.0 vlan 110 ifindex 2
ip interface "Client2" address 10.2.141.1 mask 255.255.255.0 vlan 111 ifindex 3
ip interface "Client3" address 10.2.142.1 mask 255.255.255.0 vlan 112 ifindex 4
ip interface "Client4" address 10.2.143.1 mask 255.255.255.0 vlan 113 ifindex 5
ip interface "Server" address 10.2.128.1 mask 255.255.255.0 vlan 100 ifindex 6
ip interface "Transfer_Firewall" address 192.168.150.1 mask 255.255.255.0 vlan 150 ifindex 7
! IPv6:
! IPSec:
! IPMS:
! AAA:
aaa authentication console "local"
aaa authentication ftp "local"
aaa authentication http "local"
aaa authentication snmp "local"
aaa authentication ssh "local"
user password-size min 6
! NTP:
ntp server 192.168.2.253
ntp client admin-state enable
! QOS:
policy condition from_voip source vlan 103
policy action set_dscp dscp 46
policy rule prio_voip condition from_voip action set_dscp
qos apply
! Policy Manager:
! VLAN Stacking:
! ERP:
! MVRP:
! LLDP:
lldp nearest-bridge port 1/1/1-20 tlv management system-capabilities enable
lldp nearest-bridge port 1/1/1-20 tlv management system-description enable
lldp nearest-bridge port 1/1/1-20 tlv management system-name enable
lldp nearest-bridge port 1/1/1-20 tlv management port-description enable
lldp non-tpmr port 1/1/1-20 tlv management system-capabilities enable
lldp non-tpmr port 1/1/1-20 tlv management system-description enable
lldp non-tpmr port 1/1/1-20 tlv management system-name enable
lldp non-tpmr port 1/1/1-20 tlv management port-description enable
lldp nearest-customer port 1/1/1-20 tlv management system-capabilities enable
lldp nearest-customer port 1/1/1-20 tlv management system-description enable
lldp nearest-customer port 1/1/1-20 tlv management system-name enable
lldp nearest-customer port 1/1/1-20 tlv management port-description enable
lldp nearest-bridge port 1/1/1-20 tlv management management-address enable
lldp non-tpmr port 1/1/1-20 tlv management management-address enable
lldp nearest-customer port 1/1/1-20 tlv management management-address enable
lldp nearest-bridge port 2/1/1-20 tlv management system-capabilities enable
lldp nearest-bridge port 2/1/1-20 tlv management system-description enable
lldp nearest-bridge port 2/1/1-20 tlv management system-name enable
lldp nearest-bridge port 2/1/1-20 tlv management port-description enable
lldp non-tpmr port 2/1/1-20 tlv management system-capabilities enable
lldp non-tpmr port 2/1/1-20 tlv management system-description enable
lldp non-tpmr port 2/1/1-20 tlv management system-name enable
lldp non-tpmr port 2/1/1-20 tlv management port-description enable
lldp nearest-customer port 2/1/1-20 tlv management system-capabilities enable
lldp nearest-customer port 2/1/1-20 tlv management system-description enable
lldp nearest-customer port 2/1/1-20 tlv management system-name enable
lldp nearest-customer port 2/1/1-20 tlv management port-description enable
lldp nearest-bridge port 2/1/1-20 tlv management management-address enable
lldp non-tpmr port 2/1/1-20 tlv management management-address enable
lldp nearest-customer port 2/1/1-20 tlv management management-address enable
! UDLD:
! Server Load Balance:
! High Availability Vlan:
! Session Manager:
session cli timeout 30
session http timeout 30
session prompt default "CORE01 ->"
command-log enable
! Web:
! Trap Manager:
snmp station 192.168.2.203 162 "snmpv3" v3 enable
! Health Monitor:
! System Service:
swlog output socket 192.168.2.203
system timezone CET
! SNMP:
snmp security authentication set
snmp community-map mode enable
snmp community-map "public" user "snmp" enable
! BFD:
! IP Route Manager:
ip static-route 0.0.0.0/0 gateway 192.168.150.253 metric 1
! VRRP:
! UDP Relay:
! RIP:
! OSPF:
! ISIS:
! IP Multicast:
! DVMRP:
! IPMR:
! RIPng:
! OSPF3:
! BGP:
! Netsec:
! Module:
! RDP:
! DA-UNP:
! DHL:
! Ethernet-OAM:
! SAA:
! SPB-ISIS:
! SVCMGR:
! LDP:
! EVB:

Carry out the MC-LAG to OmniSwitch Virtual-Chassis migration

Preparation of CORE01

Create the directories for Virtual-Chassis and open vcsetup.cfg:

CORE01 -> mkdir vc-config
CORE01 -> cd vc-config
CORE01 -> vi vcsetup.cfg
(Edit file, like in the following example)

This example follows the previous configuration of the multi-chassis/VFL-ports, this is worthwhile in most cases.

vcsetup.cfg

!========================================!
! File: /flash/vc-config/vcsetup.cfg     !
!========================================!
! Virtual Chassis Manager:
virtual-chassis chassis-id 1 configured-chassis-id 1
virtual-chassis chassis-id 1 vf-link 0 create       
virtual-chassis chassis-id 1 vf-link 0 member-port 1/1/1 
virtual-chassis chassis-id 1 vf-link 0 member-port 1/1/20
virtual-chassis chassis-id 1 chassis-group 9             
 
! IP:                                                                     
ip interface local chassis-id 1 emp address 192.168.1.1 mask 255.255.255.0

We strongly recommend to use and configure the EMP-port (Out-of-Band-Management), which is important to use „Remote-Chassis-Split-Detection“ which avoids a „Split-Brain“-situation!

Upload/Copy the Alcatel-Lucent Operating System (AOS):

Upload the vcboot.cfg via FTP to the directory vc-config!

CORE01 -> 
CORE01 -> ls
vcboot.cfg   vcsetup.cfg
CORE01 -> cp ../732-344-GA/Tos.img .
CORE01 -> ls -l
-rw-r--r--    1 admin    user     126642216 Aug 16 09:51 Tos.img
-rw-------    1 admin    user          8279 Aug 16 09:50 vcboot.cfg
-rw-r--r--    1 admin    user           497 Aug 16 09:49 vcsetup.cfg
CORE01 ->

Preparation of CORE02

Create the directories for Virtual-Chassis and open vcsetup.cfg:

CORE02 -> mkdir vc-config
CORE02 -> cd vc-config
CORE02 -> vi vcsetup.cfg
(Edit file, like in the following example)

This example follows the previous configuration of the multi-chassis/VFL-ports, this is worthwhile in most cases.

vcsetup.cfg

!========================================!
! File: /flash/vc-config/vcsetup.cfg     !
!========================================!
! Virtual Chassis Manager:
virtual-chassis chassis-id 2 configured-chassis-id 2
virtual-chassis chassis-id 2 vf-link 0 create       
virtual-chassis chassis-id 2 vf-link 0 member-port 2/1/1 
virtual-chassis chassis-id 2 vf-link 0 member-port 2/1/20
virtual-chassis chassis-id 2 chassis-group 9             
 
! IP:                                                                     
ip interface local chassis-id 2 emp address 192.168.1.2 mask 255.255.255.0

We strongly recommend to use and configure the EMP-port (Out-of-Band-Management), which is important to use „Remote-Chassis-Split-Detection“ which avoids a „Split-Brain“-situation!

Upload/Copy the Alcatel-Lucent Operating System (AOS):

Upload the vcboot.cfg via FTP to the directory vc-config!

CORE02 -> 
CORE02 -> ls
vcboot.cfg   vcsetup.cfg
CORE02 -> cp ../732-344-GA/Tos.img .
CORE02 -> ls -l
-rw-r--r--    1 admin    user     126642216 Aug 16 09:51 Tos.img
-rw-------    1 admin    user          8279 Aug 16 09:50 vcboot.cfg
-rw-r--r--    1 admin    user           497 Aug 16 09:49 vcsetup.cfg
CORE02 ->

Reboot the two nodes/chassis

CORE01:

CORE01 -> reload from vc-config no rollback-timeout

CORE02:

CORE02 -> reload from vc-config no rollback-timeout

Relevant output on console

We're waiting for Chassis Supervision: CMM has reached the ready state [L8], in that moment the Virtual-Chassis is ready and starts to switch/forward traffic.

Fri Aug 16 10:03:44 : vcmCmm chas_sup info message:
+++ CMM:vcmCMM_cs_handle_chassis_ready@3602: Chassis 1 ready (data 0) [L1]
 
Fri Aug 16 10:04:05 : vcmCmm port_mgr info message:
+++ CMM:vcmCMM_client_rx_pm@1551: VFL link 1/0 up (pri 1/1/1:0x0) [L2]

Fri Aug 16 10:04:05 : vcmCmm protocol info message:
+++ CMM:vcmCMN_protocol_ready_update_cb@13348: Chassis 1, role Master, status Running, master 1 [L3]

Fri Aug 16 10:04:05 : vcmCmm ipc info message:
+++ CMM:vcmCMM_peer_connected@1792: Remote endpoint (chassis 2, slot 65) [L4]

Fri Aug 16 10:04:08 : vcmCmm node_sync info message:
+++ CMM:notify_sync_complete@757: Sync complete 'multi node' (peers 1, conn 1, sync 1) [L5]

Fri Aug 16 10:04:08 : ChassisSupervisor bootMgr info message:
+++ Sending VC Takeover to NIs and applications [L6]

Fri Aug 16 10:04:08 : isis_spb_0 TASK info message:
+++ VC Takeover: chassis_id:1

Fri Aug 16 10:04:08 : ipv4 itf info message:
+++ Interface EMP-CHAS1 192.168.1.1/255.255.255.0

Fri Aug 16 10:04:08 : SNMP aluSubagent_thread info message:
+++ snmp_vc_takeover_callback | VC Takeover complete

Fri Aug 16 10:04:10 : qosNi Info info message:
+++ VC Takeover in progress.
+++ VC Takeover complete.

Fri Aug 16 10:04:10 : ChassisSupervisor bootMgr info message:
+++ Received VC Takeover Complete event from all apps [L7]
Chassis Supervision: CMM has reached the ready state [L8]
Chassis Supervision: CMM has reached the ready state [L8]

Fri Aug 16 10:04:12 : ChassisSupervisor reloadMgr info message:
+++ Redundancy time expired - updating next running to vc-config

The time it took since reload and „ready state“-message:

Verify the Virtual-Chassis topology

CORE01 -> show virtual-chassis topology 
Local Chassis: 1
                                        Config 
 Chas  Role         Status              Chas ID  Pri   Group  MAC-Address      
-----+------------+-------------------+--------+-----+------+------------------
 1     Master       Running             1        100   9      e8:e7:32:11:ca:ed
 2     Slave        Running             2        100   9      e8:e7:32:11:ca:d1

Finalising the VC migration

After you've verified that everything works as expected, you should save and certify the configuration.

CORE01 -> write memory flash-synchro