Benutzer-Werkzeuge

Webseiten-Werkzeuge


aos_release_6_aos_release_7_cli_delta

AOS Release 6 zu AOS Release 7 CLI Delta

Mit Einführung von AOS Release 7 wurde die CLI verbessert. Dabei wurde insbesondere auf die Rückmeldungen von Partnern/Kunden eingangen.

  • Verwendung von Port-Ranges
  • Einheitliche Verwendung von „admin-state“
  • „no“ ist, wo es sinnvoll ist, zu Beginn der Zeile
  • Ab AOS 7.3.1.R01 ist es möglich Kommandos abzukürzen „sh ip int“ anstatt „show ip interfaces“
  • Bei Spanning-Tree wird einheitlich „spantree“ für alle Kommandos verwendet

CHASSIS SUPERVISION

6.4.2.R01 Command 7.1.1.R01 Command
reload [primary | secondary | all] [with-fabric] [in [hours:] minutes | at hour:minute [month day | day month] | cancel] reload [primary | secondary | all] [in [hours:] minutes | at hour:minute [month day | day month] | cancel]
reload working {rollback-timeout minutes | no rollback-timeout} [in [hours:] minutes | at hour:minute] reload from <image-dir> {rollback-timeout minutes | no rollback-timeout} [redundancy-time <redundancy-time>] [in [hours:] minutes | at hour:minute]
new command issu from <image-dir> redundancy-time <redundancy-time>
[configure] copy running-config working removed
[configure] write memory write memory
[configure] write memory flash-synchro write memory flash-synchro
[configure] copy working certified [flash-synchro] copy running certified [flash-synchro]
[configure] copy certified working copy certified <image-directory> [make-running-directory]
[configure] copy flash-synchro no change
new command modify running-directory <image-directory>
takeover [with-fabric] takeover
show running-directory no change
show reload [status | all status] no change
show microcode [issu | working | certified | loaded] show microcode [issu | working | certified | loaded | <directory>]
show microcode history [working | certified] removed
system contact text_string no change
system name text_string no change
system location text_string no change
system date [mm/dd/yyyy] no change
system time [hh:mm:ss] no change
system time-and-date synchro removed
system timezone [timezone_abbrev | offset_value | time_notation] system timezone [timezone_abbrev | time_notation]
system daylight savings time [{enable | disable} | start {week} {day} in {month} at {hh:mm} end {week} {day} in {month} at {hh:mm} [by min]] system daylight-savings-time
reload ni [slot] number reload slot <number>
reload pass-through slot-number removed
power ni [slot] slot-number power slot <slot[-slot]>
no power ni [slot] slot-number no power slot <slot[-slot]>
temp-threshold temp slot slot-number no change
new command [no] powersupply enable [<psu-id>]
rcp rem-slot:[path/]src_filename [path/]dst_filename no change
rdf rdf [slot-nr]
rls <string> [<string>] rls rem-slot <path> [<filename>]
rrm <string> <string> rrm rem-slot <[path/]filename>
stack set slot slot-number saved-slot saved-slot-number [reload] no change
stack clear slot slot-number no change
show system no change
show hardware info show hardware-info
show chassis [number] no change
show cmm [number] show cmm [<number> | <cmm_letter>]
show ni [number] show slot [<slot-nr>]
new command show transceivers [slot <slot-nr> [transceiver <transceiver_num>]]
show module [number] show module[<number> | <cmm_letter>]
show module long [number] show module long [<number> | <cmm_letter>]
show module status [number] show module status [<number> | <cmm_letter>]
show power [supply] [number] show powersupply [<number>]
show fan [number] no change
new command show fantray [<fantray-nr>]
show temperature [number] show temperature [fabric [<index>] | slot [<index>] | fantray [<index>] | cmm [<index> | <cmm_letter>]]
show stack topology [slot-number] removed: not supported
show stack status removed: not supported
hash-control brief moved to CapMan
hash-control extended [[no] udp-tcp-port] moved to CapMan
show hash-control moved to CapMan
new command show escalation-strategy [<slot-id>]
license apply removed: not supported
show license info removed: not supported
show license file removed: not supported
debug chassis auto-reboot enable|disable removed
debug chassis auto-reboot ni enable|disable removed
debug chassis hello timers enable|disable removed
debug chassis secondary emp {enable | disable} removed
debug chassis hello {enable | disable} removed
debug chassis show removed
debug chassis show state trace removed
debug chassis show application context all removed
new command debug show boardinfo
update fpga { [cmm [<slot>]] | [ni { <slot> | all }] [daughter <num>] {file <file-name>} } no change

DHCP RELAY

6.4.2.R01 Command 7.1.1.R01 Command
642Commands 711Commands
ip helper address ip_address no change
ip helper no address [ip_address] no ip helper address <ip_address>*
ip helper address ip_address vlan vlan_id ip helper vlan <vlan1[-vlan2]> address <ip_address>*
ip helper no address ip_address vlan vlan_id no ip helper vlan <vlan1[-vlan2]> address <ip_address>*
ip helper standard no change
ip helper avlan only removed
ip helper per-vlan only ip helper per-vlan-only
ip helper forward delay seconds ip helper forward-delay <seconds>
ip helper maximum hops hops ip helper maximum-hops <hops>
ip helper agent-information {enable | disable} no change
ip helper agent-information policy {drop | keep | replace} no change
ip helper pxe-support {enable | disable} no change
ip helper traffic-suppression {enable | disable} removed
ip helper dhcp-snooping {enable | disable} removed
ip helper dhcp-snooping mac-address verification {enable | disable} removed
ip helper dhcp-snooping option-82 data-insertion {enable | disable} removed
ip helper dhcp-snooping option-82 data-insertion format {base-mac | system-name | userstring string | interface-alias | auto-interface-alias} removed
ip helper dhcp-snooping bypass option-82-check {enable | disable} removed
ip helper dhcp-snooping vlan vlan_id [mac-address verification {enable | disable}] [option-82 data-insertion {enable | disable}] removed
no ip helper dhcp-snooping vlan vlan_id removed
ip helper dhcp-snooping port slot1/port1[-port1a] {block | client-only | trust} removed
ip helper dhcp-snooping linkagg num {block | client-only | trust} removed
ip helper dhcp-snooping port slot1/port1[-port1a] traffic-suppression {enable | disable} removed
ip helper dhcp-snooping port slot1/port1[-port1a] ip-source-filtering {enable | disable} removed
ip helper dhcp-snooping port binding {[enable | disable] | [mac_address port slot/port address ip_address vlan vlan_id]} removed
no ip helper dhcp-snooping port binding mac_address port slot/port address ip_address vlan vlan_id removed
ip helper dhcp-snooping port binding timeout seconds removed
ip helper dhcp-snooping port binding action {purge | renew} removed
ip helper dhcp-snooping binding persistency {enable | disable} removed
ip helper boot-up {enable | disable} no change
ip helper boot-up enable {BOOTP | DHCP} no change
ip udp relay {BOOTP | NBDD | NBNSNBDD | DNS | TACACS | TFTP | NTP | port [name]} ip udp relay service {TFTP | TACACS | NTP | NBNS | NBDD | DNS} [description <desc>]
ip udp relay port <port> [description <desc>]
no ip udp relay {BOOTP | NBDD | NBNSNBDD | DNS | TACACS | TFTP | NTP | port} ip udp relay no service {TFTP | TACACS | NTP | NBNS | NBDD | DNS}
ip udp relay no port <port>
ip udp relay {BOOTP | NBDD | NBNSNBDD | DNS | TACACS | TFTP | NTP | port} vlan vlan_id ip udp relay service {TFTP | TACACS | NTP | NBNS | NBDD | DNS} [description <desc>] vlan <vlan1[-vlan2]>
ip udp relay port <port> [description <desc>] vlan <vlan1[-vlan2]>
no ip udp relay {BOOTP | NBDD | NBNSNBDD | DNS | TACACS | TFTP | NTP | port} vlan vlan_id ip udp relay service {TFTP | TACACS | NTP | NBNS | NBDD | DNS} no vlan <vlan1[-vlan2]>
ip udp relay port <port> no vlan <vlan1[-vlan2]>
new command ip udp relay no statistics
show ip helper no change
show ip helper stats show ip helper statistics
ip helper no stats no ip helper statistics
show ip helper dhcp-snooping vlan removed
show ip helper dhcp-snooping port removed
show ip helper dhcp-snooping binding removed
show ip udp relay service [BOOTP | NBDD | NBNSNBDD | DNS | TACACS | TFTP | NTP | port] show ip udp relay service {TFTP | TACACS | NTP | NBNS | NBDD | DNS}
show ip udp relay [BOOTP | NBDD | NBNSNBDD | DNS | TACACS | TFTP | NTP | port] show ip udp relay port <port>
show ip udp relay destination [BOOTP | NBDD | NBNSNBDD | DNS | TACACS | TFTP | NTP | port] show ip udp relay
show ip udp relay statistics show ip udp relay statistics service {TFTP | TACACS | NTP | NBNS | NBDD | DNS}
show ip udp relay statistics [BOOTP | NBDD | NBNSNBDD | DNS | TACACS | TFTP | NTP | port] show ip udp relay statistics port <port>
show ip udp relay statistics

DVMRP

6.4.2.R01 Command 7.1.1.R01 Command
642Commands 711Commands
VRP Prefix has been added to all cmds [{vrf vrf_name}]
ip load dvmrp remaining cmd no change
ip dvmrp status {enable | disable} ip dvmrp admin-state {enable | disable}
ip dvmrp flash-interval seconds remaining cmd no change
ip dvmrp graft-timeout seconds remaining cmd no change
ip dvmrp interface {interface_name} remaining cmd no change
no ip dvmrp interface {interface_name} remaining cmd no change
ip dvmrp interface {interface_name} metric value remaining cmd no change
ip dvmrp neighbor-interval seconds remaining cmd no change
ip dvmrp neighbor-timeout seconds remaining cmd no change
ip dvmrp prune-lifetime seconds remaining cmd no change
ip dvmrp prune-timeout seconds remaining cmd no change
ip dvmrp report-interval seconds remaining cmd no change
ip dvmrp route-holddown seconds remaining cmd no change
ip dvmrp route-timeout seconds remaining cmd no change
ip dvmrp subord-default {true | false} remaining cmd no change
ip dvmrp tunnel {local_name} {remote_address} removed: functionality replaced by 'ip interface <name> tunnel [source <ip_address>] [destination <ip_address>] [protocol {ipip | gre}]'
no ip dvmrp tunnel {local_name} {remote_address} removed: functionality replaced by 'no ip dvmrp interface <name>'
ip dvmrp tunnel {interface_name remote_address} ttl value removed
show ip dvmrp remaining cmd no change
show ip dvmrp interface [ip_address | interface_name | enabled | disabled] remaining cmd no change
show ip dvmrp neighbor [ip_address] remaining cmd no change
show ip dvmrp nexthop [ip_address ip_mask] remaining cmd no change
show ip dvmrp prune [group_address source_address source_mask] remaining cmd no change
show ip dvmrp route [ip_address ip_mask] remaining cmd no change
show ip dvmrp tunnel [local_address remote_address] remaining cmd no change

MULTI-CHASSIS

6.4.2.R01 Command 7.1.1.R01 Command
MULTI-CHASSIS CHASSIS-ID <chassisId> [IPC-VLAN <vlan>] [HELLO-INTERVAL <interval>] no change
MULTI-CHASSIS {IPC-VLAN <vlan> | HELLO-INTERVAL <interval>} no change
NO MULTI-CHASSIS CHASSIS-ID no change
MULTI-CHASSIS VIP-VLAN {<vlan[-vlan2]>} [ENABLE | DISABLE] MULTI-CHASSIS VIP-VLAN {<vlan[-vlan2]>} [ADMIN-STATE {ENABLE | DISABLE}] [NAME <name>] [MTU-IP <size>]
NO MULTI-CHASSIS VIP-VLAN {<vlan[-vlan2]>} no change
MULTI-CHASSIS VF-LINK CREATE no change
NO MULTI-CHASSIS VF-LINK no change
MULTI-CHASSIS VF-LINK MEMBER-PORT <slot/port> no change
NO MULTI-CHASSIS VF-LINK MEMBER-PORT <slot/port> no change
MULTI-CHASSIS VF-LINK DEFAULT-VLAN <vlan> no change
MULTI-CHASSIS LOOP-DETECTION {ENABLE | DISABLE} no change
MULTI-CHASSIS LOOP-DETECTION TRANSMIT-INTERVAL <interval> no change
SHOW MULTI-CHASSIS STATUS no change
SHOW MULTI-CHASSIS LOOP-DETECTION no change
SHOW MULTI-CHASSIS VF-LINK no change
SHOW MULTI-CHASSIS VF-LINK MEMBER-PORT [<slot/port>] no change
SHOW MULTI-CHASSIS CONSISTENCY no change
SHOW MULTI-CHASSIS CONSISTENCY LINKAGG <aggId> no change
DEBUG SHOW MULTI-CHASSIS LINKAGG [<aggId>] VLAN-LIST no change
DEBUG SHOW MULTI-CHASSIS INFO no change

SYSTEM SERVICES

6.4.2.R01 Command 7.1.1.R01 Command
UPDATE {MINIBOOT | UBOOT-MINIBOOT} removed
update uboot cmm [<int>] [file <filename>] no change
update uboot ni {<int> | all} [file <filename>] no change
show update uboot cmm [<int>] no change
show update uboot ni {<int> | all} no change
MORE [<string> | SIZE] replaced by linux version of command: more
NO MORE removed
SHOW MORE removed
LS [-R] [<string>] replaced by linux version of command: ls
RM [-R] [<string>] replaced by linux version of command: rm
CP [-R] [<string>] replaced by linux version of command: cp
FSCK /FLASH [REPAIR | NO-REPAIR] removed
FSCK /UFLASH [REPAIR | NO-REPAIR] no change
NEWFS /FLASH removed
DSHELL removed
VIEW <string> removed
TFTP {<string> | <ip_address>} {GET | PUT} SOURCE-FILE <string> [ASCII | DESTINATION-FILE <string>] removed
MOUNT [/UFLASH] no change
UMOUNT /UFLASH no change
NEWFS /UFLASH no change
BACKUP <string> <string> removed
RESTORE <string> [DISPLAY-ONLY | <string>] removed
FREESPACE [/FLASH] freespace [/flash | /uflash]
new command usb {enable | disable}
new command usb auto-copy {enable | disable}
new command show usb statistics
NO KTRACE removed
SFTP <dest_address> replaced by linux version of command: sftp
SSH {<dest_address> | ENABLE | DISABLE | ENFORCE PUBKEY-AUTH {ENABLE | DISABLE}} replaced by linux version of command: ssh
SSH6 <dest_address> removed
SFTP6 <dest_address> removed
SHOW SSH CONFIG removed
show history history
history size <size> removed
show history parameters removed
DEBUG KTRACE [SHOW [LOG] | APPID <appid> LEVEL <level> | NO APPID <appid> | ENABLE | DISABLE] removed
DEBUG SYSTRACE {ENABLE | DISABLE | SHOW [LOG <string>] | APPID <appid> LEVEL <level> | NO APPID <appid> | WATCH {ENABLE | DISABLE}} removed
DEBUG ED <string> removed
DEBUG TASKTRACE SHOW LOG removed
SHOW SWLOG show swlog [appid {<appname> | all}]
SHOW LOG SWLOG [TIMESTAMP <date> <time> | SESSION <int> | APPID <app> | LEVEL <level>] show log swlog [slot <slot>]
SWLOG CONSOLE LEVEL level no change
SWLOG OUTPUT opt_output no change
NO SWLOG OUTPUT opt_output no change
SWLOG CLEAR swlog clear [slot {<int> | all}]
SWLOG OUTPUT FLASH FILE-SIZE integer swlog output flash-file-size <size>
SWLOG OUTPUT SOCKET ipv6Address opt_integer optUserCmdHost no change
NO SWLOG OUTPUT SOCKET ipv6Address no change
SWLOG OUTPUT SOCKET ipAddress opt_integer optUserCmdHost no change
NO SWLOG OUTPUT SOCKET ipAddress no change
SWLOG REMOTE COMMAND-LOG on_off no change
SWLOG SYSLOG-FACILITY-ID syslogFacilityIdList no change
[NO] SWLOG swlog [appid {<appname> | all} subapp {<0-31> | all}] {enable | disable}
SWLOG APPID appIdList LEVEL level swlog appid <name> subapp <0-31> level <num> [vrf <vrf>]
NO SWLOG APPID appIdList removed
new command [no] swlog preamble
new command [no] swlog duplicate-detect
new command [no] debug swlog
new command swlog hash-time-limit <limit>
new command swlog output tty {enable | disable}
session banner {cli | ftp | http} <file_name > session {cli|ftp|http} banner <file_name>
session banner no {cli | ftp | http} no session {cli|ftp|http} banner
session timeout {cli | http | ftp} <minutes> session {cli|ftp|http} timeout <minutes>
session {ftp | tftp | sftp | telnet} port <port> ip service {ftp | ssh | telnet} port {default | <port>}
session prompt default <string> no change
who no change
kill <pid> no change
show session config no change
whoami no change
tty <int> <int> no change
show tty no change
chmod {+w | -w} <string> no change
session login-timeout <val> no change
session login-attemp <val> no change
command-log {enable | disable} no change
show command-log [status] no change
show session xon-off no change
session xon-off {enable | disable} no change
IP DOMAIN-LOOKUP no change
NO IP DOMAIN-LOOKUP no change
IP NAME-SERVER {<ip_address>}+ no change
NO IP NAME-SERVER {ALL | <ip_address>} no change
IP DOMAIN-NAME <domain-name> no change
NO IP DOMAIN-NAME no change
SHOW DNS no change
IPV6 NAME-SERVER {ipv6Address}+ no change
NSLOOKUP {string | <ip_address>} no change
AUTO KEYWORD COMPLETION [enable | disable] no change
NO AUTO KEYWORD COMPLETION no change
VERBOSE HELP [enable | disable] no change
NO VERBOSE HELP no change
SHOW PREFIX no change
NO PREFIX no change
USER PROFILE {SAVE | RESET} no change
PROMPT [none | time | system | user | date | prefix | string <prompt>] no change
modify boot parameters no change
upgrade ni <int> license-key <"string"> removed
exit replaced by linux version of command: exit
kill <int> no change
alias <string> <string> replaced by linux version of command: alias
no alias [all | <string>] replaced by linux version of command: unalias
show alias [all | <string>] replaced by linux version of command: alias
cd [<directory>] replaced by linux version of command: cd
pwd replaced by linux version of command: pwd
mkdir [<directory>] replaced by linux version of command: mkdir
rmdir [<directory>] replaced by linux version of command: rmdir
dir [<directory>] replaced by linux version of command: ls
rename <file1> <file2> replaced by linux version of command: mv
delete <file> replaced by linux version of command: rm
mv <file1> <string> replaced by linux version of command: mv
move <file1> <string> replaced by linux version of command: mv
attrib {+w | -w} <string> removed: same command as chmod
ftp {<string> | <ip_address>} replaced by linux version of command: ftp
vi <filename> replaced by linux version of command: vi
telnet {<string> | <ip_address>} replaced by linux version of command: telnet
scp {<string> | <ip_address>} {<string> | <ip_address>} replaced by linux version of command: scp
aclman removed
rz removed
install {<string>}+ removed
scp-sftp {enable | disable} removed
ftp6 {<string> | <ipv6_address>} <interface> removed
telnet6 {<string> | <ipv6_address>} <interface> removed
debug memory monitor {enable | disable} removed
debug memory monitor show log [global | task | size] removed
debug memory monitor show status removed
show log pmd <string> [type <string> | id <id> | taskname <name> | taskid <id> | record <string> | address <int> | subid <int>] removed
debug show pmd <int> <int> <int> <int> removed
debug pmd show <int> <int> <int> <int> removed
debug remove pmd <int> <int> <int> <int> removed
debug pmd remove <int> <int> <int> <int> removed
debug dump pmd <int> <int> <int> <int> <string> removed
debug pmd dump <int> <int> <int> <int> <string> removed
debug pmd ni removed
AUTO KEYWORD COMPLETION [ENABLE | DISABLE] removed: not supported
NO AUTO KEYWORD COMPLETION removed: not supported
PROMPT [NONE] [TIME | SYSTEM | USER | DATE | PREFIX | STRING <string>]* removed: use 'export PS1="prompt string->"

AAA

6.4.2.R01 Command 7.1.1.R01 Command
AAA RADIUS AGENT PREFERRED {DEFAULT | NO-LOOPBACK | <ip_address>} removed
NO AAA RADIUS AGENT PREFERRED removed
new command USER admin CONSOLE-ONLY {ENABLE | DISABLE}
USER “user_name” END-USER-PROFILE <string> removed
USER “user_name” NO END-USER-PROFILE removed
END-USER PROFILE removed
NO END-USER PROFILE removed
SHOW END-USER PROFILE removed
DEBUG END-USER PROFILE removed
SHOW USER PASSWORD-EXPIRATION removed
SHOW USER PASSWORD-SIZE removed
AAA RADIUS-AGENT removed
AAA ACE-SERVER removed

BFD

6.4.2.R01 Command 7.1.1.R01 Command
All cmds have optional VRF prefix [vrf {vrf_name}] All cmds have optional VRF prefix [vrf {vrf_name}]
ip bfd-std status {enable | disable} ip bfd admin-state {enable | disable}
ip bfd-std transmit transmit-interval ip bfd transmit <transmit-interval>
ip bfd-std receive receive-interval ip bfd receive <receive-interval>
ip bfd-std mode {echo-only | demand echo {enable | disable} | asynchronous echo {enable|disable}} ip bfd mode {echo-only | demand [echo-state {enable | disable}] | asynchronous [echo-state {enable | disable}] }
ip bfd-std echo status {enable | disable} ip bfd echo-state {enable | disable}
ip bfd-std echo interval echo-interval ip bfd echo-interval <echo-interval>
ip bfd-std 12-hold-timer l2-holdtimer-interval ip bfd 12-hold-timer <l2-holdtimer-interval>
ip bfd-std interface interface_name ip bfd interface <interface_name>
no ip bfd-std interface interface_name no ip bfd interface <interface_name>
ip bfd-std interface interface_name status {enable | disable} ip bfd interface <interface_name> admin-state {enable | disable}
ip bfd-std interface interface_name transmit transmit-interval ip bfd interface <interface_name> transmit <transmit-interval>
ip bfd-std interface interface_name receive receive-interval ip bfd interface <interface_name> receive <receive-interval>
ip bfd-std interface interface_name multiplier multiplier_value ip bfd interface <interface_name> multiplier <multiplier_value>
ip bfd-std interface interface_name echo-interval echo-interval ip bfd interface <interface_name> echo-interval <echo-interval>
ip bfd-std interface interface_name mode {echo-only | demand [echo {enable | disable}] | asynchronous [echo {enable|disable}} ip bfd interface <interface_name> mode {echo-only | demand [echo-state {enable | disable}] | asynchronous [echo-state {enable | disable}] }
ip bfd-std interface interface_name 12-hold-timer l2-holdtimer-interval ip bfd interface <interface_name> 12-hold-timer <l2-holdtimer-interval>
ip ospf bfd-std status {enable | disable} ip ospf bfd-state {enable | disable}
[no] ip ospf bfd-std all-interfaces ip ospf bfd-state all-interfaces {enable | disable}
ip ospf interface interface-name bfd-std {enable | disable} ip ospf interface <interface-name> bfd-state {enable | disable}
ip ospf interface interface-name bfd-std drs-only ip ospf interface <interface-name> bfd-state drs-only
ip ospf interface interface-name bfd-std all-nbrs ip ospf interface <interface-name> bfd-state all-neighbors {enable | disable}
ip bgp bfd-std status {enable | disable} ip bgp bfd-state {enable | disable}
[no] ip bgp bfd-std all-neighbors ip bgp bfd-state all-neighbors {enable | disable}
ip bgp neighbor name bfd-std {enable | disable} ip bgp neighbor <ip_address> bfd-state {enable | disable}
vrrp bfd-std {enable | disable} vrrp bfd-state {enable | disable}
vrrp track num address address bfd-std {enable| disable} vrrp track <num> address <address> bfd-state {enable| disable}
show ip bfd-std show ip bfd
show ip bfd-std interfaces [interface-name] show ip bfd interfaces [<interface-name>]
show ip bfd-std [session <num> ] [sessions [slot <num>] show ip bfd sessions [<num>] [slot <num>]
new command ip bfd multiplier <num>
new command show ip bfd sessions statistics [<num>]

BGP

6.4.2.R01 Command 7.1.1.R01 Command
642 Commands 711 Commands
VRF Prefix on all ipv4 (ip) cmds [vrf {vrf_name}] VRF Prefix on all ipv4 (ip) cmds [vrf {vrf_name}]
ip load bgp no change
ip bgp status {enable | disable} ip bgp admin-state {enable | disable}
ip bgp unicast no change
no ip bgp unicast no change
ip bgp autonomous-system value no change
ip bgp bestpath as-path ignore no change
no ip bgp bestpath as-path ignore no change
ip bgp cluster-id ip_address no change
ip bgp default local-preference value no change
ip bgp fast-external-failover no change
no ip bgp fast-external-failover no change
ip bgp always-compare-med no change
no ip bgp always-compare-med no change
ip bgp bestpath med missing-as-worst no change
no ip bgp bestpath med missing-as-worst no change
ip bgp client-to-client reflection no change
no ip bgp client-to-client reflection no change
ip bgp as-origin-interval seconds no change
no ip bgp as-origin-interval no change
ip bgp synchronization no change
no ip bgp synchronization no change
ip bgp confederation identifier value no change
ip bgp maximum-paths no change
no ip bgp maximum-paths no change
ip bgp log-neighbor-changes no change
no ip bgp log-neighbor-changes no change
ip bgp dampening [half-life half_life reuse reuse suppress suppress max-suppress-time max_suppress_time] no change
no ip bgp dampening no change
ip bgp dampening clear no change
ip bgp aggregate-address ip_address ip_mask no change
no ip bgp aggregate-address ip_address ip_mask no change
ip bgp aggregate-address ip_address ip_mask status {enable | disable} ip bgp aggregate-address <ip_address> <ip_mask> admin-state {enable | disable}
ip bgp aggregate-address ip_address ip_mask as-set no change
no ip bgp aggregate-address ip_address ip_mask as-set no change
ip bgp aggregate-address ip_address ip_mask community string no change
ip bgp aggregate-address ip_address ip_mask local-preference value no change
no ip bgp aggregate-address ip_address ip_mask local-preference value no change
ip bgp aggregate-address ip_address ip_mask metric value no change
no ip bgp aggregate-address ip_address ip_mask metric value no change
ip bgp aggregate-address ip_address ip_mask summary-only no change
no ip bgp aggregate-address ip_address ip_mask summary-only no change
ip bgp network network_address ip_mask no change
no ip bgp network network_address ip_mask no change
ip bgp network network_address ip_mask status {enable | disable} ip bgp network <network_address> <ip_mask> admin-state {enable | disable}
ip bgp network network_address ip_mask community string no change
ip bgp network network_address ip_mask local-preference value no change
no ip bgp network network_address ip_mask local-preference value no change
ip bgp network network_address ip_mask metric value no change
no ip bgp network network_address ip_mask metric value no change
ip bgp neighbor ip_address no change
no ip bgp neighbor ip_address no change
ip bgp neighbor ip_address status {enable | disable} ip bgp neighbor <ip_address> admin-state {enable | disable}
ip bgp neighbor ip_address advertisement-interval value no change
ip bgp neighbor ip_address clear no change
ip bgp neighbor ip_address route-reflector-client no change
no ip bgp neighbor ip_address route-reflector-client no change
ip bgp neighbor ip_address default-originate no change
no ip bgp neighbor ip_address default-originate no change
ip bgp neighbor ip_address timers keepalive holdtime no change
ip bgp neighbor ip_address conn-retry-interval seconds no change
ip bgp neighbor ip_address auto-restart no change
ip bgp neighbor ip_address maximum-prefix maximum [warning-only] no change
ip bgp neighbor ip_address md5 key {string | none} no change
ip bgp neighbor ip_address md5 key-encrypt encrypted_string no change
ip bgp neighbor ip_address ebgp-multihop [ttl] no change
no ip bgp neighbor ip_address ebgp-multihop no change
ip bgp neighbor ip_address description string no change
ip bgp neighbor ip_address next-hop-self no change
no ip bgp neighbor ip_address next-hop-self no change
ip bgp neighbor ip_address passive no change
no ip bgp neighbor ip_address passive no change
ip bgp neighbor ip_address remote-as value no change
ip bgp neighbor ip_address remove-private-as no change
no ip bgp neighbor ip_address remove-private-as no change
ip bgp neighbor ip_address soft-reconfiguration no change
no ip bgp neighbor ip_address soft-reconfiguration no change
ip bgp neighbor ip_address stats-clear no change
ip bgp confederation neighbor ip_address no change
no ip bgp confederation neighbor ip_address no change
ip bgp neighbor ip_address update-source [interface_name] no change
ip bgp neighbor ip_address in-aspathlist {string | none} no change
ip bgp neighbor ip_address in-communitylist {string | none} no change
ip bgp neighbor ip_address in-prefixlist {string | none} no change
ip bgp neighbor peer_address in-prefix6list pfx_list_name no change
ip bgp neighbor peer_address out-prefix6list pfx_list_name no change
ip bgp neighbor ip_address out-aspathlist {string | none} no change
ip bgp neighbor ip_address out-communitylist {string | none} no change
ip bgp neighbor ip_address out-prefixlist {string | none} no change
ip bgp neighbor ip_address route-map {string | none} {in | out} no change
no ip bgp neighbor ip_address route-map {in | out} no change
ip bgp neighbor ip_address clear soft {in | out} no change
ip bgp policy aspath-list name “regular_expression” no change
no ip bgp policy aspath-list name “regular_expression” no change
ip bgp policy aspath-list name “regular_expression” action {permit | deny} no change
ip bgp policy aspath-list name “regular_expression” priority value no change
ip bgp policy community-list name {none | no-export | no-advertise | no-export-subconfed | num:num} no change
no ip bgp policy community-list name {none | no-export | no-advertise | no-export-subconfed | num:num} no change
ip bgp policy community-list name {none | no-export | no-advertise | no-export-subconfed | num:num} action {permit | deny} no change
ip bgp policy community-list name {none | no-export | no-advertise | no-export-subconfed | num:num} match-type {exact | occur} no change
ip bgp policy community-list name {none | no-export | no-advertise | no-export-subconfed | num:num} priority value no change
ip bgp policy prefix-list name ip_address ip_mask no change
no ip bgp policy prefix-list name ip_address ip_mask no change
ip bgp policy prefix-list name ip_address ip_mask action {permit | deny} no change
ip bgp policy prefix-list name ip_address ip_mask ge value no change
ip bgp policy prefix-list name ip_address ip_mask le value no change
ip bgp policy prefix6-list pfx_list_name prefix6/pfx_length [action{permit|deny}] [status{enable|disable}] [ge[{masklength}]] [le[{masklength}]] ip bgp policy prefix6-list <pfx_list_name> <prefix6/pfx_length> [action{permit|deny}] [admin-state {enable|disable}] [ge[{<masklength>}]] [le[{<masklength>}]]
no ip bgp policy prefix6-list pfx_list_name prefix6/pfx_length [action{permit|deny}] no change
ip bgp policy route-map name sequence_number no change
ip bgp policy route-map name sequence_number action {permit | deny} no change
ip bgp policy route-map name sequence_number aspath-list as_name no change
ip bgp policy route-map name sequence_number asprepend path no change
ip bgp policy route-map name sequence_number community [none | no-export | no-advertise | no-export-subconfed | num:num] no change
ip bgp policy route-map name sequence_number community-list name no change
ip bgp policy route-map name sequence_number community-mode {add | replace} no change
ip bgp policy route-map name sequence_number lpref value no change
ip bgp policy route-map name sequence_number lpref-mode {none | inc | dec | rep} no change
ip bgp policy route-map name sequence_number match-community [none | no-export | noadvertise | no-export-subconfed | num:num] no change
ip bgp policy route-map name sequence_number match-mask ip_address no change
ip bgp policy route-map name sequence_number match-prefix ip_address no change
ip bgp policy route-map name sequence_number match-regexp “regular_expression” no change
ip bgp policy route-map name sequence_number med value no change
ip bgp policy route-map name sequence_number med-mode {none | inc | dec | rep} no change
ip bgp policy route-map name sequence_number origin {igp | egp| incomplete | none} no change
ip bgp policy route-map name sequence_number prefix-list prefix_name no change
ip bgp policy route-map name sequence_number weight value no change
ip bgp policy route-map name sequence_number community-strip community_list no change
show ip bgp no change
show ip bgp statistics no change
show ip bgp dampening no change
show ip bgp dampening-stats [ip_address ip_mask] [peer_address] no change
show ip bgp path no change
show ip bgp routes [network_address ip_mask] no change
show ip bgp aggregate-address [ip_address ip mask] no change
show ip bgp network [network_address ip_mask] no change
show ip bgp neighbors [ip_address] no change
show ip bgp neighbors policy ipv4_address no change
show ip bgp neighbors timer [ip_address] no change
show ip bgp neighbors statistics [ip_address] no change
show ip bgp policy aspath-list [name] [“regular_expression”] no change
show ip bgp policy community-list [name] [string] no change
show ip bgp policy prefix-list [name] [ip_address ip_mask] no change
show ip bgp policy prefix6-list [pfx_list_name[{prefix6/prefix_length}]] no change
show ip bgp policy route-map [name] [sequence_number] no change
ip bgp graceful-restart no change
no ip bgp graceful-restart no change
ip bgp graceful-restart restart-interval [seconds] no change
ipv6 bgp unicast no change
no ipv6 bgp unicast no change
ip bgp neighbor ip_address activate-ipv6 no change
no ip bgp neighbor ip_address activate-ipv6 no change
ip bgp neighbor ip_address ipv6-nexthop ipv6_address no change
show ipv6 bgp path [ipv6-addr ipv6_address/prefix_length] no change
show ipv6 bgp routes no change
ipv6 bgp network ipv6_address/prefix_length no change
no ipv6 bgp network ipv6_address/prefix_length no change
ipv6 bgp network ipv6_address/prefix_length [community {none | num | num:num}] no change
ipv6 bgp network ipv6_address/prefix_length [local-preference num] no change
ipv6 bgp network ipv6_address/prefix_length [metric num] no change
ipv6 bgp network ipv6_address/prefix_length [status {enable | disable}] ipv6 bgp network <ipv6_address/prefix_length> [admin-state {enable | disable}]
show ipv6 bgp network [ipv6_address/prefix_length] no change
ipv6 bgp neighbor ipv6_address no change
no ipv6 bgp neighbor ipv6_address no change
ipv6 bgp neighbor peer6_address clear soft {in | out} no change
ipv6 bgp neighbor peer6_address soft-reconfiguration no change
no ipv6 bgp neighbor peer6_address soft-reconfiguration no change
ipv6 bgp neighbor peer6_address in-prefix6list pfx_list_name no change
ipv6 bgp neighbor peer6_address out-prefix6list pfx_list_name no change
ipv6 bgp neighbor ipv6_address [activate-ipv6] no change
no ipv6 bgp neighbor ipv6_address [activate-ipv6] no change
ipv6 bgp neighbor ipv6_address [ipv6-nexthop ipv6_address] no change
ipv6 bgp neighbor ipv6_address [status {enable | disable}] ipv6 bgp neighbor <ipv6_address> [admin-state {enable | disable}]
ipv6 bgp neighbor ipv6_address [remote-as num] no change
ipv6 bgp neighbor ipv6_address [timers num num] no change
ipv6 bgp neighbor ipv6_address [maximum-prefix num [warning-only]] no change
no ipv6 bgp neighbor ipv6_address [maximum-prefix num [warning-only]] no change
ipv6 bgp neighbor ipv6_address [next-hop-self] no change
no ipv6 bgp neighbor ipv6_address [next-hop-self] no change
ipv6 bgp neighbor ipv6_address [conn-retry-interval num] no change
ipv6 bgp neighbor ipv6_address [default-originate] no change
no ipv6 bgp neighbor ipv6_address [default-originate] no change
ipv6 bgp neighbor ipv6_address [update-source interface_name] no change
no ipv6 bgp neighbor ipv6_address [update-source interface_name] no change
ipv6 bgp neighbor ipv6_address [ipv4-nexthop ip_address] no change
show ipv6 bgp neighbors [ipv6_address] no change
show ipv6 bgp neighbors statistics [ipv6_address] no change
show ipv6 bgp neighbors timers [ipv6_address] no change
show ipv6 bgp neighbors policy ipv6_address no change

CAPABILITY MANAGER

6.4.2.R01 Command 7.1.1.R01 Command
hash-control brief no change
hash-control extended [[no] udp-tcp-port] no change
new command hash-control load-balance non-ucast {enable | disable}
show hash-control no change
new command show hash-control non-ucast
new command show escalation-strategy [<slot-id>]

CONFIG MANAGER

6.4.2.R01 Command 7.1.1.R01 Command
configuration apply <filename> [verbose] no change
configuration syntax check <filename> [verbose] configuration syntax-check <filename> [verbose]
configuration apply <filename> [<time>] no change
show configuration status no change
configuration cancel no change
configuration snapshot <appname> no change
show configuration snapshot [<appname>] no change
configuration error-file limit <limit> configuration error-file-limit <limit>
SHOW TECH-SUPPORT no change
SHOW TECH-SUPPORT LAYER2 no change
SHOW TECH-SUPPORT LAYER3 no change
SHOW TECH-SUPPORT LAYER3 RIP no change
SHOW TECH-SUPPORT LAYER3 OSPF no change
SHOW TECH-SUPPORT LAYER3 BGP no change
SHOW TECH-SUPPORT LAYER3 PIM no change
SHOW TECH-SUPPORT LAYER3 MROUTE no change
SHOW TECH-SUPPORT LAYER3 DVMRP no change
SHOW TECH-SUPPORT LAYER3 IPV6 no change
SHOW TECH-SUPPORT LAYER3 RIPNG no change
SHOW TECH-SUPPORT LAYER3 OSPF3 no change
SHOW TECH-SUPPORT LAYER3 ISIS no change
SHOW TECH-SUPPORT LAYER3 PIM6 no change
SHOW TECH-SUPPORT LAYER3 IPSEC no change
SHOW TECH-SUPPORT LAYER3 BFD no change

ERP

6.4.2.R01 Command 7.1.1.R01 Command
642Commands 711Commands
erp-ring ring_id port1 {slot/port | linkagg agg_num} port2 {slot/port | linkagg agg_num} service-vlan vlan_id level level_num [guard-timer guard_timer] [wait-torestore- timer wtr_timer] [enable | disable] no change
no erp-ring ring_id no change
erp-ring ring_id rpl-node {port slot/port | linkagg agg_num} no change
no erp-ring ring_id rpl-node no change
erp-ring ring_id wait-to-restore wtr_timer no change
no erp-ring ring_id wait-to-restore no change
erp-ring ring_id {enable | disable} no change
erp-ring ring_id ethoam-event {port slot/port | linkagg agg_num} remote-endpoint mep_id no change
no erp-ring ring_id ethoam-event {port slot/port | linkagg agg_num} no change
erp-ring ring_id guard-timer guard_timer no change
no erp-ring ring_id guard-timer no change
clear erp statistics [ring ring_id [port slot/port | linkagg agg_num]] no change
show erp [ring ring_id | [port slot/port | linkagg agg_num]] no change
show erp [ring ring_id] protected-vlan no change
show erp statistics [ring ring_id [port slot/port | linkagg agg_num]] no change
new command erp-ring <ring_id> {port <slot/port> | linkagg <id>} virtual-sf-monitor {enable | disable}

ESM

6.4.2.R01 Command 7.1.1.R01 Command
642Commands 711Commands
interfaces {<slot> | <slot/port[-port2]>} {admin | autoneg } {enable|disable} interfaces {<slot> | <slot/port[-port2]>} {admin-state | autoneg } {enable|disable}
trap slot[/port[-port2]] port link {enable | disable | on | off} interfaces {<slot> | <slot/port1[-port2]>} link-trap {enable|disable}
interfaces {<slot> | <slot/port[-port2]>} crossover {mdix | mdi | auto} no change
interfaces {<slot> | <slot/port[-port2]>} duplex {half | full | auto} no change
interfaces slot[/port[-port2]] speed {auto | 10 | 100 | 1000 | 10000 | max {100 | 1000}} interfaces {<slot> | <slot/port1[-port2]>} speed {10 | 100 | 1000 | auto | max {100 | 1000}}
interfaces {<slot> | <slot/port[-port2]>} pause {tx-and-rx|tx|rx|disable} no change
new command interfaces {<slot> | <slot/port1[-port2]>]} flood-limit {bcast|mcast|uucast|all} rate { pps <num> | mbps <num> | cap% <num> | enable | disable}
interfaces {<slot> | <slot/port[-port2]>} max frame <size> interfaces {<slot> | <slot/port1[-port2]>} max-frame-size <size>
interfaces {<slot> | <slot/port[-port2]>} no l2 statistics [cli] clear interfaces {<slot> | <slot/port1[-port2]>} l2-statistics [cli]
interfaces {<slot> | <slot/port[-port2]>} port {<string> | <num>} interfaces {<slot> | <slot/port1[-port2]>} alias {<string> | <num>}
interfaces transceiver ddm [trap] {enable | disable} interfaces ddm[-trap] {enable | disable}
new command interfaces {<slot> | <slot/port1[-port2]>} ingress-bandwidth {mbps <num> [burst <mbits>] | enable | disable}
show interfaces [<slot> | <slot/port[-port2]>] {status | capability | flood rate | port | accounting | counters | traffic | pause} show interfaces [<slot> | <slot/port1[-port2]>] {status | capability | flood-rate | port | accounting | counters [errors] | traffic}
new command show interfaces [<slot> | <slot/port1[-port2]>] ingress-rate-limit
show interfaces transceiver [<slot> | <slot/port[-port2]>] transceiver [ddm | w-low | w-high | a-low | a high | actual] show interfaces [<slot> | <slot/port1[-port2]>] ddm [w-low | w-high | a-high | a-low | actual | status]
show interfaces [<slot> | <slot/port[-port]>] port show interfaces [<slot> | <slot/port[-port]>] alias
interfaces slot[/port[-port2]] hybrid removed: not supported at the moment
show interfaces [slot[/port[-port2]]] hybrid removed: not supported at the moment
interfaces {<slot> | <slot/port[-port2]>} {ifg <num> | flow {enable | disable} | clear-violation-all | runt <num> | runtsize <num> | register {lwm | dyncell} regval <num> | pause} removed
intefaces [no] e2e-flow-vlan removed
interfaces cli-prompt {enable | disable} removed
10gig slot <slot> {phys-a | phys-b} removed
show interfaces [<slot> | <slot/port[-port2]>] {e2e-flow-vlan | flow | collisions | ifg | register {lwm | dyncell}} removed
show 10gig [slot <slot>] removed
debug interfaces [<slot> | <slot/port[port2]>] {backpressure [enable | disable] | automix {enable | disable} | mac [nonport | port | stats] | phy | led | mdix} removed
debug interfaces set <slot/port> {mdix | automdix | linkled [activity]} {enable | disable} removed
debug interfaces <slot> switching <hexNum> [<num>] removed
debug interfaces [slot] backpressure removed
debug interfaces set [slot] backpressure {enable | disable} removed

GVRP

6.4.2.R01 Command 7.1.1.R01 Command
642Commands 711Commands
Not Supported ATM
clear gvrp statistics [port <slot/port> | linkagg <agg>] no change
[no] gvrp transparent-switching no change
gvrp registration {normal | fixed | forbidden} {port <slot/port> | linkagg <agg>} no change
no gvrp registration {port <slot/port> | linkagg <agg>} no change
gvrp applicant {participant | non-participant | active} {port <slot/port> | linkagg <agg>} no change
no gvrp applicant {port <slot/port> | linkagg <agg>} no change
[no] gvrp restrict-vlan-registration {port <slot/port> | linkagg <agg>} <vlan[-vlan]> no change
[no] gvrp static vlan-restrict {port <slot/port> | linkagg <agg>} <vlan[-vlan]> [no] gvrp static-vlan-restrict {port <slot/port> | linkagg <agg>} <vlan[-vlan]>
gvrp timer {join | leave | leaveall} <time> {port <slot/port> | linkagg <agg>} no change
no gvrp timer {join | leave | leaveall} {port <slot/port> | linkagg <agg>} no change
show gvrp timer [join | leave | leaveall] [port <slot/port> | linkagg <agg>] no change
show gvrp statistics [port <slot/port> | linkagg <agg>] no change
[no] gvrp no change
[no] gvrp {port <slot/port> | linkagg <agg>} no change
show gvrp last-pdu-origin {port <slot/port> | linkagg <agg>} no change
show gvrp configuration [port [<slot/port>] | linkagg <agg>] no change
gvrp maximum vlan <limit> gvrp maximum-vlan <limit>
[no] gvrp restrict-vlan-advertisement {port <slot/port> | linkagg <agg>} <vlan[-vlan]> no change

HEALTH MONITOR

6.4.2.R01 Command 7.1.1.R01 Command
health threshold {rx percent | txrx percent | memory percent | cpu percent} no change
health threshold temperature degrees removed
health interval seconds no change
health statistics reset removed
show health threshold [rx | txrx | memory | cpu | temperature] show health configuration
show health interval show health configuration
show health [statistics] show health
show health {slot/port} [statistics] show health {port <slot/port> | slot <slot>} [statistics]
show health all {memory | cpu | rx | txrx} no change
show health slice slot removed
show health fabric slot1[-slot2] removed

HTTP

6.4.2.R01 Command 7.1.1.R01 Command
[no] { http | https } server webview server { enable | disable }
new command webview access { enable | disable }
[no] { http | https } ssl webview force-ssl { enable | disable }
{ http | https } port { default | <port> } webview http-port { default | <port> }
new command webview https-port { default | <port> }
show http show webview
debug http removed

IPSEC

6.4.2.R01 Command 7.1.1.R01 Command
ipsec key key_name {sa-authentication | sa-encryption} key no change
ipsec security-key [old_key] new_key no change
ipsec policy policy_name [priority priority] [source {ipv6_address [/prefix_length]} [port port]] [destination {ipv6_address [/prefix_length]}[port port]] [protocol protocol}] [in | out] [discard | ipsec | none] [description description] [no shutdown | shutdown] ipsec policy policy_name [priority priority] [source {ipv6_address [/prefix_length]} [port port]] [destination {ipv6_address [/prefix_length]}[port port]] [protocol protocol}] [in | out] [discard | ipsec | none] [description description] [admin-state {enable | disable}]
no ipsec policy policy_name no change
ipsec policy policy_name rule index [ah | esp] no change
no ipsec policy policy_name rule index no change
ipsec sa sa_name {esp | ah} [source ipv6_address] [destination ipv6_address] [spi spi] [encryption {null | des-cbc | 3des-cbc | aes-cbc [key-size key_length] | aes-ctr [key-size key_length]}] [authentication {none | hmac-md5 | hmacsha1 | aes-xcbc-mac}] [description description] [no shutdown | shutdown] ipsec sa sa_name {esp | ah} [source ipv6_address] [destination ipv6_address] [spi spi] [encryption {null | 3des-cbc | aes-cbc [key-size key_length]}] [authentication {none | hmac-md5 | hmacsha1 | aes-xcbc-mac}] [description description] [admin-state {enable | disable}]
no ipsec sa name no change
show ipsec policy [policy_name] no change
show ipsec sa [sa_name | esp | ah] no change
show ipsec key {sa-encryption | sa-authentication} no change
show ipsec ipv6 statistics no change

IPV4

6.4.2.R01 Command 7.1.1.R01 Command
VRF Prefix on all cmds [vrf {vrf_name}] VRF Prefix on all cmds [vrf {vrf_name}]
ip interface name [address ip_address] [mask subnet_mask] [vlan vid] [forward | no forward] [local-proxy-arp | no local-proxy-arp] [e2 | snap] [primary | no primary] no change
new command variation for virtual chassis ip interface name [address ip_address] [mask subnet_mask] [vlan <virtual-chassis-vlan-id>] vip-address <ip_address>
ip interface name admin {enable | disable} ip interface <name> admin-state {<enable> | <disable>}
no ip interface name no change
ip interface name tunnel [source ip_address] [destination ip_address] [protocol {ipip | gre}] no change
ip router primary-address ip_address no change
ip router router-id ip_address no change
ip static-route ip_address [mask mask] gateway gateway [metric metric] ip static-route ip_address [mask mask] {gateway gateway | follows ip_address} [metric metric]
no ip static-route ip_address [mask mask] gateway ip_address [metric metric] no ip static-route ip_address [mask mask] {gateway ip_address | follows ip_address} [metric metric]
ip static-route ip_address [mask mask] gateway gateway bfd-std {enable | disable} ip static-route ip_address [mask mask] gateway gateway bfd-state {enable | disable}
ip static-route all bfd-std {enable | disable} ip static-route all bfd-state {enable | disable}
ip route-pref {static | ospf | rip | ebgp | ibgp} value no change
ip default-ttl hops no change
ping {ip_address | hostname} [count count] [size packet_size] [interval seconds] [timeout seconds] no change
traceroute {ip_address | hostname} [max-hop max_hop_count] no change
ip directed-broadcast {on | off} no change
ip service {all | service_name | port service_port} no change
no ip service {all | service_name | port service_port} vlan types removed from service_name and service port
new command ip service {ftp | ssh | telnet} port {default | <port>}
new command [no] ip service access [<ip_interface_name>]
ip redist {local | static | rip | ospf | isis | bgp} into {rip | ospf | isis | bgp} route-map route-mapname [status {enable | disable}] no change
no ip redist {local | static | rip | ospf | isis | bgp} into {rip | ospf | bgp} [route-map route-mapname] no change
ip access-list access-list-name no change
no ip access-list access-list-name no change
ip access-list access-list-name address address/prefixLen [action {permit | deny}] [redist-control {all-subnets | no-subnets | aggregate}] no change
no ip access-list access-list-name address address/prefixLen no change
ip route-map route-map-name [sequence-number number] match ip-nexthop {access-list-name | ip_address/prefixLen [permit | deny]} no change
no ip route-map route-map-name [sequence-number number] match ip-nexthop {access-list-name | ip_address/prefixLen [permit | deny]} no change
ip route-map route-map-name [sequence-number number] match ipv6-nexthop {access-list-name | ipv6_address/prefixLen [permit | deny]} no change
no ip route-map route-map-name [sequence-number number] match ipv6-nexthop {access-list-name | ipv6_address/prefixLen [permit | deny]} no change
ip route-map route-map-name [sequence-number number] match ipv4-interface interfacename no change
no ip route-map route-map-name [sequence-number number] match ipv4-interface interfacename no change
ip route-map route-map-name [sequence-number number] match ipv6-interface interfacename no change
no ip route-map route-map-name [sequence-number number] match ipv6-interface interfacename no change
ip route-map route-map-name [sequence-number number] match metric metric [deviation deviation] no change
no ip route-map route-map-name [sequence-number number] match metric metric [deviation deviation] no change
ip route-map route-map-name [sequence-number number] match route-type {internal | external [type1 | type2] | level1 | level2} no change
no ip route-map route-map-name [sequence-number number] match route-type {internal | external [type1 | type2] | level1 | level2} no change
ip route-map route-map-name [sequence-number number] set metric metric [effect {add | subtract | replace | none}] no change
no ip route-map route-map-name [sequence-number number] set metric metric [effect {add | subtract | replace | none}] no change
ip route-map route-map-name [sequence-number number] set metric-type {internal | external [type1 | type2]} no change
no ip route-map route-map-name [sequence-number number] set metric-type {internal | external [type1 | type2]} no change
ip route-map route-map-name [sequence-number number] set tag tag-number no change
no ip route-map route-map-name [sequence-number number] set tag tag-number no change
ip route-map route-map-name [sequence-number number] set community community-string no change
no ip route-map route-map-name [sequence-number number] set community communitystring no change
ip route-map route-map-name [sequence-number number] set local-preference value no change
no ip route-map route-map-name [sequence-number number] set local-preference value no change
ip route-map route-map-name [sequence-number number] set level {level1 | level2 | level1-2} no change
no ip route-map route-map-name [sequence-number number] set level {level1 | level2 | level1-2} no change
ip route-map route-map-name [sequence-number number] set ip-nexthop ip_address no change
no ip route-map route-map-name [sequence-number number] set ip-nexthop ip_address no change
ip route-map route-map-name [sequence-number number] set ipv6-nexthop ipv6_address no change
no ip route-map route-map-name [sequence-number number] set ipv6-nexthop ipv6_address no change
vrf [name | default] no change
no vrf name no change
arp ip_address hardware_address [alias] [arp-name] [<slot/port>] arp <ip_address> <hardware_address> [alias] [<arp-name>] [port <slot/port>] [linkagg <agg_num>]
no arp ip_address [alias] no change
clear arp-cache no change
ip dos arp-poison restricted-address ip_address no change
no ip dos arp-poison restricted-address ip_address no change
arp filter ip_address [mask ip_mask] [vid] [sender | target] [allow | block] no change
no arp filter ip_address no change
clear arp filter no change
icmp type type code code {{enable | disable} | min-pkt-gap gap} no change
icmp unreachable [net-unreachable | host-unreachable | protocol-unreachable | port-unreachable] {{enable | disable} | min-pkt-gap gap} no change
icmp echo [request | reply] {{enable | disable} | min-pkt-gap gap} no change
icmp timestamp [request | reply] {{enable | disable} | min-pkt-gap gap} no change
icmp addr-mask [request | reply] {{enable | disable} | min-pkt-gap gap} no change
icmp messages {enable | disable} no change
ip dos scan close-port-penalty penalty_value no change
ip dos scan tcp open-port-penalty penalty_value no change
ip dos scan udp open-port-penalty penalty_value no change
ip dos scan threshold threshold_value no change
ip dos trap {enable | disable} no change
ip dos scan decay decay_value no change
show ip traffic no change
show ip interface [name | emp | vlan vlan id] no change
show ip route [summary] show ip routes [summary]
show ip route-pref no change
show ip redist [rip | ospf | bgp] no change
show ip access-list [access-list-name] no change
show ip route-map [route-map-name] no change
show ip router database [protocol type | gateway ip_address | dest {ip_address/prefixLen | ip_address}] no change
show ip emp-route show ip emp-routes
show ip config no change
show ip protocols no change
new command show ip router-id
show ip service no change
show vrf no change
show arp [ip_address | hardware_address] no change
show arp summary no change
show arp filter [ip_address] no change
show icmp control no change
show icmp [statistics] no change
show tcp statistics no change
show tcp ports no change
show udp statistics no change
show udp ports no change
show ip dos config no change
show ip dos statistics no change
show ip dos arp-poison no change

IPV6

6.4.2.R01 Command 7.1.1.R01 Command
ipv6 interface if_name [vlan vid | tunnel {tid | 6to4}] [base-reachable-time time] [ra-send {yes | no}] [ra-max-interval interval] [ra-managed-config-flag {true | false}] [ra-other-config-flag {true | false}] [ra-reachable-time time] [ra-retrans-timer time] [ra-default-lifetime time | no ra-default-lifetime] [ra-send-mtu] {yes | no} new options [no ra-min-interval] [ra-cli-skew]
ipv6 interface if_name {enable | disable} ipv6 interface <if_name> admin-state {enable | disable}
no ipv6 interface if_name no change
ipv6 address ipv6_address /prefix_length [anycast] {if_name | loopback} no change
no ipv6 address ipv6_address [anycast] {if_name | loopback} no change
ipv6 address ipv6_prefix eui-64 {if_name | loopback} no change
no ipv6 address ipv6_prefix eui-64 {if_name | loopback} no change
ipv6 address global-id {generate | globalID} no change
ipv6 address local-unicast [global-id globalID] [subnet-id subnetID] {interface-id interfaceID | eui-64} [prefix-length prefixLength] {if-name | loopback} no change
[no] ipv6 address local-unicast [global-id globalID] [subnet-id subnetID] {interface-id interfaceID | eui-64} [prefix-length prefixLength] {if-name | loopback} no change
ipv6 interface if_name tunnel {[source ipv4_source] [destination ipv4_destination]} no change
ipv6 dad-check ipv6_address if_name no change
ipv6 hop-limit value no change
no ipv6 hop-limit no change
ipv6 pmtu-lifetime time no change
ipv6 host name ipv6_address removed
no ipv6 host name ipv6_address no change
ipv6 neighbor stale-lifetime stale-lifetime no change
ipv6 neighbor ipv6_address hardware_address {if_name} slot/port ipv6 neighbor <ipv6_address> <hardware_address> <if_name> {port <slot/port> | linkagg <agg_id>}
no ipv6 neighbor ipv6_address {if_name} no change
ipv6 prefix ipv6_address /prefix_length if_name [valid-lifetime time] [preferred-lifetime time] [on-link-flag {true | false} [autonomous-flag {true | false}] if_name no change
no ipv6 prefix ipv6_address /prefix_length if_name no change
ipv6 route ipv6_prefix/prefix_length ipv6_address [if_name] no change
no ipv6 route ipv6_prefix/prefix_length ipv6_address [if_name] no change
ipv6 static-route ipv6_prefix/prefix_length gateway ipv6_address [if_name] [metric metric] no change
no ipv6 static-route ipv6_prefix/prefix_length gateway ipv6_address [if_name] no change
ipv6 route-pref {static | ospf | rip | ebgp | ibgp} value no change
ping6 {ipv6_address | hostname} [if_name] [count count] [size data_size] [interval seconds] no change
traceroute6 {ipv6_address | hostname} [if_name] [max-hop hop_count] [wait-time time] [port port_number] [probe-count probe] new options [size size_value] [host-names {yes|no}]
show ipv6 hosts [substring] removed
show ipv6 icmp statistics [if_name] no change
show ipv6 interface [if_name | loopback] no change
show ipv6 pmtu table no change
clear ipv6 pmtu table removed
show ipv6 neighbors [ipv6_prefix/prefix_length | if_name | hw hardware_address | static] no change
clear ipv6 neighbors no change
show ipv6 prefixes no change
show ipv6 routes [ipv6_prefix/prefix_length | static] no change
show ipv6 route-pref no change
show iv6p router database [protocol type | gateway ipv6_address | dest ipv6_prefix/prefix_length] no change
show ipv6 tcp ports removed
new command show ipv6 tcp connections
new command show ipv6 tcp listeners
clear ipv6 traffic removed
show ipv6 tunnel no change
show ipv6 udp ports no change
show ipv6 information no change
ipv6 redist {local | static | rip | ospf | isis | bgp} into {rip | ospf | isis | bgp} route-map routemap-name [status {enable | disable}] ipv6 redist {local | static | rip | ospf | isis | bgp} into {rip | ospf | isis | bgp} route-map <routemap-name> [admin-state {enable | disable}]
ipv6 access-list access-list-name no change
no ipv6 access-list access-list-name no change
ipv6 access-list access-list-name address address/prefixLen [action {permit | deny}] [redist-control {all-subnets | no-subnets | aggregate}] no change
no ipv6 access-list access-list-name address address/prefixLen no change
show ipv6 redist [rip | ospf | bgp] no change
show ip access-list [access-list-name] no change
ipv6 load rip no change
ipv6 rip status {enable | disable} ipv6 rip admin-state {enable | disable}
ipv6 rip invalid-timer seconds no change
ipv6 rip garbage-timer seconds no change
ipv6 rip holddown-timer seconds no change
ipv6 rip jitter value no change
ipv6 rip route-tag value no change
ipv6 rip update-interval seconds no change
ipv6 rip triggered-sends {all | updated-only | none} no change
ipv6 rip interface if_name no change
[no] ipv6 rip interface if_name no change
ipv6 rip interface if_name metric value no change
ipv6 rip interface if_name recv-status {enable | disable} no change
ipv6 rip interface if_name send-status {enable | disable} no change
ipv6 rip interface if_name horizon {none | split-only | poison} no change
show ipv6 rip no change
show ipv6 rip interface [if_name] no change
show ipv6 rip peer [ipv6_addresss] no change
show ipv6 rip routes [dest <ipv6_prefix/prefix_length>] | [gateway <ipv6_addr>] | [detail <ipv6 prefix/prefix_length>] no change
6.4.2.R01 Command 7.1.1.R01 Command
static linkagg agg_num size size [name name] [admin state {enable | disable}] linkagg static agg <agg_num1[-agg_num2]> size size [name name] [admin-state {enable | disable}] [multi-chassis active]
no static linkagg agg_num no linkagg static agg <agg_num1[-agg_num2]>
static linkagg agg_num name name linkagg static agg <agg_num1[-agg_num2]> name name
static linkagg agg_num no name no linkagg static agg <agg_num1[-agg_num2]> name
static linkagg agg_num admin state {enable | disable} linkagg static agg <agg_num1[-agg_num2]> admin-state {enable | disable}
static agg slot/port agg num agg_num linkagg static port <slot/port1[-port2]> agg agg_num
static agg no slot/port no linkagg static port <slot/port1[-port2]>
lacp linkagg agg_num size size linkagg lacp agg <agg_num1[-agg_num2]> size size
no lacp linkagg agg_num no linkagg lacp agg <agg_num1[-agg_num2]>
lacp linkagg agg_num name name linkagg lacp agg <agg_num1[-agg_num2]> name name
lacp linkagg agg_num no name no linkagg lacp agg <agg_num1[-agg_num2]> name
lacp linkagg agg_num admin state {enable | disable} linkagg lacp agg <agg_num1[-agg_num2]> admin-state {enable | disable}
lacp linkagg agg_num actor admin key actor_admin_key linkagg lacp agg <agg_num1[-agg_num2]> actor admin-key actor_admin_key
lacp linkagg agg_num no actor admin key no linkagg lacp agg <agg_num1[-agg_num2]> actor admin-key
lacp linkagg agg_num actor system priority actor_system_priority linkagg lacp agg <agg_num1[-agg_num2]> actor system-priority actor_system_priority
lacp linkagg agg_num no actor system priority no linkagg lacp agg <agg_num1[-agg_num2]> actor system-priority
lacp linkagg agg_num actor system id actor_system_id linkagg lacp agg <agg_num1[-agg_num2]> actor system-id actor_system_id
lacp linkagg agg_num no actor system id no linkagg lacp agg <agg_num1[-agg_num2]> actor system-id
lacp linkagg agg_num partner system id partner_system_id linkagg lacp agg <agg_num1[-agg_num2]> partner system-id partner_system_id
lacp linkagg agg_num no partner system id no linkagg lacp agg <agg_num1[-agg_num2]> partner system-id
lacp linkagg agg_num partner system priority partner_system_priority linkagg lacp agg <agg_num1[-agg_num2]> partner system-priority partner_system_priority
lacp linkagg agg_num no partner system priority no linkagg lacp agg <agg_num1[-agg_num2]> partner system-priority
lacp linkagg agg_num partner admin key partner_admin_key linkagg lacp agg <agg_num1[-agg_num2]> partner admin-key partner_admin_key
lacp linkagg agg_num no partner admin key no linkagg lacp agg <agg_num1[-agg_num2]> partner admin-key
lacp agg slot/port actor admin key actor_admin_key linkagg lacp port <slot/port1[-port2]> actor admin-key actor_admin_key
lacp agg no slot/port no linkagg lacp port <slot/port1[-port2]>
lacp agg slot/port actor admin state {[active] [timeout] [aggregate] [synchronize] [collect] [distribute] [default] [expire] | none} linkagg lacp port <slot/port1[-port2]> actor admin-state {[active] [timeout] [aggregate] [synchronize] [collect] [distribute] [default] [expire] | none}
lacp agg slot/port actor admin state {[[no] active] [[no] timeout] [[no] aggregate] [[no] synchronize] [[no] collect] [[no] distribute] [[no] default] [[no] expire] | none} no linkagg lacp port <slot/port1[-port2]> actor admin-state {[active] [timeout] [aggregate] [synchronize] [collect] [distribute] [default] [expire] | none}
lacp agg slot/port actor system id actor_system_id linkagg lacp port <slot/port1[-port2]> actor system-id actor_system_id
lacp agg slot/port no actor system id no linkagg lacp port <slot/port1[-port2]> actor system-id
lacp agg slot/port actor system priority actor_system_priority linkagg lacp port <slot/port1[-port2]> actor system-priority actor_system_priority
lacp agg slot/port no actor system priority no linkagg lacp port <slot/port1[-port2]> actor system-priority
lacp agg slot/port partner admin state {[active] [timeout] [aggregate] [synchronize] [collect] [distribute] [default] [expire] | none} linkagg lacp port <slot/port1[-port2]> partner admin-state {[active] [timeout] [aggregate] [synchronize] [collect] [distribute] [default] [expire] | none}
lacp agg slot/port partner admin state {[[no] active] [[no] timeout] [[no] aggregate] [[no] synchronize] [[no] collect] [[no] distribute] [[no] default] [[no] expire] | none} no linkagg lacp port <slot/port1[-port2]> partner admin-state {[active] [timeout] [aggregate] [synchronize] [collect] [distribute] [default] [expire] | none}
lacp agg slot/port partner admin system id partner_admin_system_id linkagg lacp port <slot/port1[-port2]> partner admin-system-id partner_admin_system_id
lacp agg slot/port no partner admin system id no linkagg lacp port <slot/port1[-port2]> partner admin-system-id
lacp agg slot/port partner admin key partner_admin_key linkagg lacp port <slot/port1[-port2]> partner admin-key partner_admin_key
lacp agg slot/port no partner admin key no linkagg lacp port <slot/port1[-port2]> partner admin-key
lacp agg slot/port partner admin system priority partner_admin_system_priority linkagg lacp port <slot/port1[-port2]> partner admin-system-priority partner_admin_system_priority
lacp agg slot/port no partner admin system priority no linkagg lacp port <slot/port1[-port2]> partner admin-system-priority
lacp agg slot/port actor port priority actor_port_priority linkagg lacp port <slot/port1[-port2]> actor port-priority actor_port_priority
lacp agg slot/port no actor port priority no linkagg lacp port <slot/port1[-port2]> actor port-priority
lacp agg slot/port partner admin port partner_admin_port linkagg lacp port <slot/port1[-port2]> partner admin-port partner_admin_port
lacp agg slot/port no partner admin port no linkagg lacp port <slot/port1[-port2]> partner admin-port
lacp agg slot/port partner admin port priority partner_admin_port_priority linkagg lacp port <slot/port1[-port2]> partner admin-port-priority partner_admin_port_priority
lacp agg slot/port no partner admin port priority no linkagg lacp port <slot/port1[-port2]> partner admin-port-priority
show linkagg [<agg_num] show linkagg agg [<agg_num1[-agg_num2]>]
show linkagg [agg_num] port [slot/port] show linkagg agg [<agg_num1[-agg_num2]>] port [slot/port]

LLDP

6.4.2.R01 Command 7.1.1.R01 Command
lldp transmit interval seconds no change
lldp transmit hold-multiplier num no change
lldp transmit delay seconds no change
lldp reinit delay seconds no change
lldp notification interval seconds no change
lldp {slot/port | slot | chassis} lldpdu {tx | rx | tx-and-rx | disable} lldp {port <slot/port[-port]> | slot <slot> | chassis} lldpdu {tx | rx | tx-and-rx | disable}
lldp {slot/port | slot | chassis} notification {enable | disable} lldp {port <slot/port[-port]> | slot <slot> | chassis} notification {enable | disable}
lldp {slot/port | slot | chassis} tlv management {port-description | system-name | systemdescription | system-capabilities | management-address} {enable | disable} lldp {port <slot/port[-port]> | slot <slot> | chassis} tlv management {port-description | system-name | systemdescription | system-capabilities | management-address} {enable | disable}
lldp {slot/port | slot | chassis} tlv dot1 {port-vlan | vlan-name} {enable | disable} lldp {port <slot/port[-port]> | slot <slot> | chassis} tlv dot1 {port-vlan | vlan-name} {enable | disable}
lldp {slot/port | slot | chassis} tlv dot3 mac-phy {enable | disable} lldp {port <slot/port[-port]> | slot <slot> | chassis} tlv dot3 mac-phy {enable | disable}
lldp {slot/port | slot | chassis} tlv med {power | capability} {enable | disable} lldp {port <slot/port[-port]> | slot <slot> | chassis} tlv med {power | capability} {enable | disable}
show lldp system-statistics no change
show lldp [slot/port] statistics show lldp [port <slot/port[-port]>] statistics
show lldp local-system no change
show lldp [slot/port | slot] local-port show lldp [port <slot/port[-port]> | slot <slot>] local-port
show lldp local-management-address no change
show lldp [slot/port | slot] remote-system show lldp [port <slot/port[-port]> | slot <slot>] remote-system
show lldp [slot/port | slot] remote-system [med {network-policy | inventory}] show lldp [port <slot/port[-port]> | slot <slot>] remote-system [med {network-policy | inventory}]
show lldp [<slot | slot/port>] config show lldp [port <slot/port[-port]> | slot <slot>] config
show lldp [<slot | slot/port>] statistics show lldp [port <slot/port[-port]> | slot <slot>] statistics
show lldp system-statistics (remains same) no change
show lldp local-management-address (remains same) no change

MULTICAST-ROUTING

6.4.2.R01 Command 7.1.1.R01 Command
VRF Prefix added to all IPv4(ip) cmds [vrf {vrf_name}]
ip mroute-boundary if_name scoped_address mask no change
no ip mroute-boundary if_name scoped_address mask no change
ipv6 mroute-boundary if_name scope scope_value no change
no ipv6 mroute-boundary if_name scope scope_value no change
ip mroute interface if_ name ttl threshold no change
show ip mroute-boundary no change
show ipv6 mroute-boundary no change
show ip mroute no change
show ip mroute interface {interface_name} no change
show ipv6 mroute interface {interface_name} no change
show ip mroute-nexthop no change
show ipv6 mroute no change
show ipv6 mroute-nexthop no change

MULTICAST

6.4.2.R01 Command 7.1.1.R01 Command
ip multicast [vlan <vlan>] status [enable | disable] ip multicast [vlan <vlan>] admin-state [enable | disable]
ipv6 multicast [vlan <vlan>] status [enable | disable] ipv6 multicast [vlan <vlan>] admin-state [enable | disable]

MVRP

6.4.2.R01 Command 7.1.1.R01 Command
mvrp {enable | disable} no change
mvrp {port <slot/port> | linkagg <agg>} {enable | disable} mvrp {port <slot/port[-port]> | linkagg <agg[-agg]>} {enable | disable}
mvrp transparent-switching {enable | disable} no change
mvrp maximum vlan <max> mvrp maximum-vlan <max>
mvrp {port <slot/port> | linkagg <agg>} registration {normal | fixed | forbidden} mvrp {port <slot/port[-port]> | linkagg <agg[-agg]>} registration {normal | fixed | forbidden}
mvrp {port <slot/port> | linkagg <agg>} applicant {participant | non-participant | active} mvrp {port <slot/port[-port]> | linkagg <agg[-agg]>} applicant {participant | non-participant | active}
mvrp {port <slot/port> | linkagg <agg>} timer {join | leave | leaveall | periodic-timer} <time> mvrp {port <slot/port[-port]> | linkagg <agg[-agg]>} timer {join | leave | leaveall | periodic-timer} <time>
mvrp {port <slot/port> | linkagg <agg>} periodic-transmission {enable | disable} mvrp {port <slot/port[-port]> | linkagg <agg[-agg]>} periodic-transmission {enable | disable}
[no] mvrp {port <slot/port> | linkagg <agg>} restrict-vlan-registration vlan <vlan-vlan> [no] mvrp {port <slot/port[-port]> | linkagg <agg[-agg]>} restrict-vlan-registration vlan <vlan-vlan>
[no] mvrp {port <slot/port> | linkagg <agg>} restrict-vlan-advertisement vlan <vlan-vlan> [no] mvrp {port <slot/port[-port]> | linkagg <agg[-agg]>} restrict-vlan-advertisement vlan <vlan-vlan>
[no] mvrp {port <slot/port> | linkagg <agg>} static-vlan-restrict vlan <vlan-vlan> [no] mvrp {port <slot/port[-port]> | linkagg <agg[-agg]>} static-vlan-restrict vlan <vlan-vlan>
mvrp opt_{port <slot/port> | linkagg <agg>} clear-statistics mvrp opt_{port <slot/port[-port]> | linkagg <agg[-agg]>} clear-statistics
show mvrp [port <slot/port> | linkagg <agg>] configuration show mvrp [port <slot/port[-port]> | linkagg <agg[-agg]>] configuration
show mvrp {port [<slot/port>] | linkagg [<agg>]} [enable | disable] show mvrp {port [<slot/port[-port]>] | linkagg [<agg[-agg]>]} [enable | disable]
show mvrp {port <slot/port> | linkagg <agg>} vlan-restrictions show mvrp {port <slot/port[-port]> | linkagg <agg[-agg]>} vlan-restrictions
show mvrp [port <slot/port> | linkagg <agg>] timer [join | leave | leaveall | periodic-timer] show mvrp [port <slot/port[-port]> | linkagg <agg[-agg]>] timer [join | leave | leaveall | periodic-timer]
show mvrp [port <slot/port> | linkagg <agg>] statistics show mvrp [port <slot/port[-port]> | linkagg <agg[-agg]>] statistics
show mvrp {port <slot/port> | linkagg <agg>} last-pdu-origin show mvrp {port <slot/port[-port]> | linkagg <agg[-agg]>} last-pdu-origin

NTP

6.4.2.R01 Command 7.1.1.R01 Command
ntp server {<ip_address> | <string>} [key <int> | version <int> | minpoll <int> | prefer] no change
no ntp server {<ip_address> | <string>} no change
show ntp client no change
show ntp server status no change
show ntp server client-list no change
show ntp server disabled-interfaces no change
show ntp server status <ip_address> no change
show ntp client server-list no change
ntp key <int> {trusted | untrusted} no change
ntp key load no change
show ntp keys no change
ntp client {enable | disable} no change
ntp broadcast-client {enable | disable} no change
ntp broadcast-delay <int> no change
ntp server synchronized no change
ntp server unsynchronized no change
ntp src-ip prefered {<ip_address> | no-loopback0 | default} no change
no ntp src-ip prefered no change
ntp broadcast {<ip_address> | <string>} [version <int> | minpoll <int>] no change
no ntp broadcast {<ip_address> | <string>} no change
ntp peer {<ip_address> | <string>} [key <int> | version <int> | minpoll <int>] no change
no ntp peer {<ip_address> | <string>} no change
ntp interface <ip_address> {enable | disable} no change
ntp master <int> no change
ntp max-associations <int> no change
ntp authenticate {enable | disable} no change
show ntp status no change
show ntp peers no change
ntp client prefered {<ip_address> | no-loopback0 | default} no change
no ntp client prefered no change

OSPF

6.4.2.R01 Command 7.1.1.R01 Command
Optional VRF Prefix on all cmds [vrf {vrf_name}] Optional VRF Prefix on all cmds [vrf {vrf_name}]
ip ospf status {enable | disable} ip ospf admin-state {enable | disable}
ip load ospf no change
ip ospf exit-overflow-interval seconds no change
ip ospf extlsdb-limit limit no change
ip ospf host ip_address tos tos [metric metric] no change
no ip ospf host ip_address tos tos no change
ip ospf mtu-checking no change
no ip ospf mtu-checking no change
ip ospf default-originate {only | always} [metric-type {type1 | type2}] [metric value] no change
no ip ospf default-originate no change
ip ospf route-tag tag no change
ip ospf spf-timer [delay delay_seconds] [hold hold_seconds] no change
ip ospf virtual-link area_id router_id [auth-type {none | simple | md5}] [auth-key key_string] [dead-interval seconds] [hello-interval seconds] [retrans-interval seconds] [transit-delay seconds] no change
no ip ospf virtual-link area_id router_id no change
ip ospf neighbor neighbor_id {eligible | non-eligible} no change
no ip ospf neighbor neighbor_id no change
ip ospf area area_id [summary {enable | disable}] | [type {normal | stub | nssa}] no change
no ip ospf area area_id no change
ip ospf area area_id default-metric tos [[cost cost] | [type {ospf | type 1 | type 2}] no change
no ip ospf area area_id default-metric tos no change
ip ospf area area_id range {summary | nssa} ip_address subnet_mask [effect {admatching | noMatching}] no change
no ip ospf area area_id range {summary | nssa} ip_address subnet_mask no change
ip ospf interface {interface_name} no change
no ip ospf interface {interface_name} no change
ip ospf interface {interface_name} status {enable | disable} ip ospf interface {<interface_name>} admin-state {enable | disable}
ip ospf interface {interface_name} area area_id no change
ip ospf interface {interface_name} auth-key key_string no change
ip ospf interface {interface_name} auth-type [none | simple | md5] no change
ip ospf interface {interface_name} dead-interval seconds no change
ip ospf interface {interface_name} hello-interval seconds no change
ip ospf interface {interface_name} md5 key_id [enable | disable] no change
ip ospf interface {interface_name} md5 key_id key key_string no change
ip ospf interface {interface_name} type {point-to-point | point-to-multipoint | broadcast | nonbroadcast} no change
ip ospf interface {interface_name} cost cost no change
ip ospf interface {interface_name} poll-interval seconds no change
ip ospf interface {interface_name} priority priority no change
ip ospf interface {interface_name} retrans-interval seconds no change
ip ospf interface {interface_name} transit-delay seconds no change
ip ospf restart-support {planned-unplanned | planned-only} no change
no ip ospf restart-support no change
ip ospf restart-interval [seconds] no change
ip ospf restart-helper [status {enable | disable}] ip ospf restart-helper [admin-state {enable | disable}]
ip ospf restart-helper strict-lsa-checking status {enable | disable} ip ospf restart-helper strict-lsa-checking admin-state {enable | disable}
ip ospf restart initiate no change
show ip ospf no change
show ip ospf border-routers [area_id] [router_id] [tos] [gateway] no change
show ip ospf ext-lsdb [linkstate-id ls_id] [router-id router_id] no change
show ip ospf host [ip_address] no change
show ip ospf lsdb [area_id] [rtr | net | netsum | asbrsum] [linkstate-id ls_id] [router-id router_id] no change
show ip ospf neighbor [ip_address] no change
show ip ospf routes [ip_addr mask tos gateway] no change
show ip ospf virtual-link [router_id] no change
show ip ospf virtual-neighbor area_id router_id no change
show ip ospf area [area_id] no change
show ip ospf area area_id range [{summary | nssa} ip_address ip_mask] no change
show ip ospf area area_id stub no change
show ip ospf interface [interface_name] no change
show ip ospf restart no change

OSPFV3

6.4.2.R01 Command 7.1.1.R01 Command
ipv6 ospf status {enable | disable} ipv6 ospf admin-state {enable | disable}
ipv6 load ospf no change
ipv6 ospf host ipv6_address [area area_id] [metric metric] no change
no ipv6 ospf host ipv6_address area area_id no change
ipv6 ospf mtu-checking no change
no ipv6 ospf mtu-checking no change
ipv6 ospf route-tag tag no change
ipv6 ospf spf-timer [delay delay_seconds] [hold hold_seconds] no change
ipv6 ospf virtual-link area area_id router router_id [dead-interval seconds] [hello-interval seconds] [retrans-interval seconds] [transit-delay seconds] no change
no ipv6 ospf virtual-link area area_id router router_id no change
ipv6 ospf area area_id [type {normal | stub [default-metric metric]}] no change
no ipv6 ospf area area_id no change
ipv6 ospf interface interface_name no change
no ipv6 ospf interface interface_name no change
ipv6 ospf interface interface_name status {enable | disable} ipv6 ospf interface interface_name admin-state {enable | disable}
no ipv6 ospf interface interface_name no change
ipv6 ospf interface interface_name area area_id no change
ipv6 ospf interface interface_name dead-interval seconds no change
ipv6 ospf interface interface_name hello-interval seconds no change
ipv6 ospf interface interface_name cost cost no change
ip ospf interface interface_name priority priority no change
ipv6 ospf interface interface_name retrans-interval interval no change
ipv6 ospf interface interface_name transit-delay delay no change
show ipv6 ospf no change
show ipv6 ospf border-routers [area area_id] [router router_id] no change
show ipv6 ospf host [ipv6_address] no change
show ipv6 ospf lsdb [area area_id] [rtr | net | netsum | asbrsum] [linkstate-id ls_id] [router-id router_id] no change
show ipv6 ospf neighbor [router ipv4_address][interface interface_name] no change
show ipv6 ospf routes [prefix ipv6_address_prefix][gateway gateway] no change
show ipv6 ospf virtual-link [router_id] no change
show ipv6 ospf area [area_id] no change
show ipv6 ospf interface [interface_name] no change

PIM

6.4.2.R01 Command 7.1.1.R01 Command
Optional VRF Prefix added to all IPv4(ip) cmds [vrf {vrf_name}]
ip load pim no change
ip pim sparse status {enable | disable} ip pim sparse admin-state {enable | disable}
ip pim dense status {enable | disable} ip pim dense admin-state {enable | disable}
ip pim static-rp group_address/prefix_length rp_address [[no] override] [priority priority] no change
ip pim rp-threshold bps no change
ip pim max-rps number no change
ip pim probe-time seconds no change
ip pim register checksum {header | full} no change
ip pim register-suppress-timeout seconds no change
ip pim spt status {enable | disable} ip pim spt admin-state {enable | disable}
ip pim state-refresh-interval seconds no change
ip pim state-refresh- limit ticks no change
ip pim state-refresh- ttl num no change
show ip pim sparse no change
show ip pim dense no change
show ip pim neighbor [ip_address] no change
show ip pim candidate-rp no change
show ip pim group-map [bsr | static-rp | ssm | dense] no change
show ip pim interface [if_name] no change
show ip pim static-rp no change
ipv6 pim sparse status {enable | disable} ipv6 pim sparse admin-state {enable | disable}
ipv6 pim dense status {enable | disable} ipv6 pim dense admin-state {enable | disable}
ipv6 pim cbsr bsr_address [priority bsr_priority] [mask-length masklen] [scope scope_value] no change
no ipv6 pim cbsr bsr_address [priority bsr_priority] [mask-length masklen] [scope scope_value] no change
ipv6 pim static-rp group_address/prefix_length rp_address [[no] override] [priority priority] no change
ipv6 pim spt status {enable | disable} ipv6 pim spt admin-state {enable | disable}
show ipv6 pim neighbor [ipv6_address] [if_name] no change
show ipv6 pim cbsr [scope scope_value] no change
show ipv6 pim bsr [scope scope_value] no change
ip pim interface no change
ip pim cbsr no change
ip pim dense group no change
ip pim ssm group no change
ip pim candidate-rp no change
ip pim invalid-joinprune-notification-period no change
ip pim invalid-register-notification-period no change
ip pim neighbor-loss-notification-period no change
ip pim invalid-rp-mapping-notification-period no change
ip pim keepalive period no change
ipv6 pim interface no change
ipv6 pim candidate-rp no change
ipv6 pim dense group no change
ipv6 pim ssm group no change
ipv6 pim rp-switchover no change
show ip pim bsr no change
show ip pim cbsr no change
show ip pim dense group no change
show ip pim ssm group no change
show ip pim groute no change
show ip pim sgroute no change
show ip pim notifications no change
show ipv6 pim sparse no change
show ipv6 pim dense no change
show ipv6 pim interface no change
show ipv6 pim candidate-rp no change
show ipv6 pim static-rp no change
show ipv6 pim group-map no change
show ipv6 pim dense group no change
show ipv6 pim ssm group no change
show ipv6 pim groute no change
show ipv6 pim sgroute no change

PMM

6.4.2.R01 Command 7.1.1.R01 Command
port mirroring port_mirror_sessionid [no] source slot/port[-port2] [slot/port[-port2]...] destination slot/port [rpmir-vlan vlan_id] [bidirectional |inport |outport] [unblocked vlan_id] [enable | disable] port-mirroring <port_mirror_sessionid> [no] source {<slot/port[-port2] [slot/port[-port2]...]>} destination <slot/port> [rpmir-vlan <vlan_id>] [bidirectional | inport | outport] [unblocked-vlan <vlan_id>] [enable | disable]
port mirroring port_mirror_sessionid {enable | disable} port-mirroring <port_mirror_sessionid> {enable | disable}
no port mirroring port_mirror_sessionid no port-mirroring <port_mirror_sessionid>
port monitoring port_monitor_sessionid source slot/port [{no file | file filename [size filesize] | [overwrite {on | off}]}] [inport | outport | bidirectional] [timeout seconds] [enable | disable] port-monitoring <port_monitor_sessionid> source <slot/port> [{no file | file <filename> [size <filesize>] | [overwrite {on | off}]}] [inport | outport | bidirectional] [timeout <seconds>] [enable | disable] [capture-type {full | brief}]
port monitoring port_monitor_sessionid {disable | pause | resume} port-monitoring <port_monitor_sessionid> {disable | pause | resume}
no port monitoring port_monitor_sessionid no port-monitoring <port_monitor_sessionid>
show port mirroring status [port_mirror_sessionid] show port-mirroring status [<port_mirror_sessionid>]
show port monitoring status [port_monitor_sessionid] show port-monitoring status [<port_monitor_sessionid>]
show port monitoring file [port_monitor_sessionid] show port-monitoring file [<port_monitor_sessionid>]

POLICY-SERVER

6.4.2.R01 Command 7.1.1.R01 Command
policy server load no change
policy server flush no change
policy server ip_address [port port_number] [preference preference] [user user_name password password] [searchbase search_string] [ssl | no ssl] no change
policy server ip_address admin {up | down} policy server ip_address admin-state {enable | disable}
no policy server ip_address [port port_number] no change
show policy server no change
show policy server long no change
show policy server statistics no change
show policy server rules no change
show policy server events no change

PORT-MANAGER

6.4.2.R01 Command 7.1.1.R01 Command
new command SHOW VIOLATION [port <slot/port[-port]> | linkagg <aggnum[-aggnum]>]
new command CLEAR VIOLATION {port <slot/port[-port]> | linkagg <aggnum[-aggnum]>}

PORT-MAPPING

6.4.2.R01 Command 7.1.1.R01 Command
port mapping port_mapping_sessionid {enable | disable} port-mapping <port_mapping_sessionid> {enable | disable}
no port mapping port_mapping_sessionid no port-mapping <port_mapping_sessionid>
port mapping session id unknown-unicast-flooding {enable | disable} port-mapping <sessionid> unknown-unicast-flooding {enable | disable}
show port mapping [port_mapping_sessionid] show port-mapping [<port_mapping_sessionid>]
port mapping <id> {unknown-unicast-flooding {enable | disable} | unidirectional | bidirectional} port-mapping <id> {unknown-unicast-flooding {enable | disable} | unidirectional | bidirectional}
port mapping <id> [user-port {<slot/port[-port]> | linkagg <agg_id> | slot <slot_id>] [network-port {<slot/port[-port]> | linkagg <agg_id> | slot <slot_id>] port-mapping <id> [user-port {<slot/port[-port]> | linkagg <agg_id> | slot <slot_id>] [network-port {<slot/port[-port]> | linkagg <agg_id> | slot <slot_id>]
port mapping <id> [no user-port {<slot/port[-port]> | linkagg <agg_id> | slot <slot_id>] [no network-port {<slot/port[-port]> | linkagg <agg_id> | slot <slot_id>] no port-mapping <id> [user-port {<slot/port[-port]> | linkagg <agg_id> | slot <slot_id>] [network-port {<slot/port[-port]> | linkagg <agg_id> | slot <slot_id>]

PORT-SECURITY

6.4.2.R01 Command 7.1.1.R01 Command
port-security {slot/port[-port2] | chassis} [enable | disable] port-security {port <slot/port[-port2]> | chassis} [learning-enable | learning-disable]
no port security slot/port[-port2] no port security {port <slot/port[-port2]>}
port-security shutdown minutes [convert-to-static {enable | disable}] port-security learning-window <minutes> [convert-to-static {enable | disable}]
port-security shutdown 0 no port-security learning-window
port-security slot/port[-port2] maximum number port-security port <slot/port[-port2]> maximum <number>
port-security slot/port[-port2] max-filtering number port-security port <slot/port[-port2]> max-filtering <number>
port-security {slot/port[-port2] | chassis} convert-to-static port-security {port <slot/port[-port2]> | chassis} convert-to-static
port-security slot/port mac mac_address [vlan vlan_id] removed
port-security slot/port no mac {all | mac_address} [vlan vlan_id] removed
port-security slot/port[-port2] mac-range [low mac_address | high mac_address | low mac_address high mac_address] port-security port <slot/port[-port2]> mac-range [low mac_address | high mac_address | low mac_address high mac_address]
port-security slot/port[-port2] violation {restrict | shutdown} port-security port <slot/port[-port2]> violation {restrict | shutdown}
port-security slot/port release removed
port-security slot/port[-port2] learn-trap-threshold <number> port-security port <slot/port[-port2]> learn-trap-threshold <number>
show port-security [slot/port[-port2] | slot] show port-security [port <slot/port[-port2]> | slot <slot>]
show port-security shutdown show port-security learning-window

QOS

6.4.2.R01 Command 7.1.1.R01 Command
qos {enable | disable} no change
qos trust ports qos trust-ports
qos no trust ports qos no trust-ports
qos default servicing mode {strict-priority | wrr [w0 w1 w2 w3 w4 w5 w6 w7] | priority-wrr [w0 w1 w2 w3 w4 w5 w6 w7] | drr] [w0 w1 w2 w3 w4 w5 w6 w7]} removed
qos forward log no change
qos no forward log no change
qos log console no change
qos no log console no change
qos log lines lines no change
qos log level level no change
qos clear log clear qos log
qos [no] classifyl3 bridged removed
qos [no] classify fragments removed
qos default bridged disposition {accept | deny | drop} removed
qos default routed disposition {accept | deny | drop} removed
qos default multicast disposition {accept | deny | drop} removed
qos stats interval seconds no change
qos nms priority removed
qos no nms priority removed
qos phones [priority priority_value | trusted] no change
qos no phones no change
qos user-port {filter | shutdown} {spoof | bgp | bpdu | rip | ospf | vrrp | dvmrp | pim | isis | dhcpserver | dns-reply} no change
qos no user-port {filter | shutdown} no change
qos quarantine mac-group mac_group no change
qos no quarantine mac-group no change
qos quarantine path url no change
qos no quarantine path no change
qos quarantine page no change
qos no quarantine page no change
debug qos [info] [config] [rule] [main] [route] [port] [msg] [sl] [ioctl] [mem] [cam] [mapper] [flows] [queue] [slot] [l2] [l3] [classifier] [nat] [sem] [pm] [ingress] [egress] no change
debug no qos [info] [config] [rule] [main] [route] [port] [msg] [sl] [ioctl] [mem] [cam] [mapper] [flows] [queue] [slot] [l2] [l3] [classifier] [nat] [sem] [pm] [ingress] [egress] no change
debug qos internal <input_string> no change
qos apply no change
qos revert no change
qos flush no change
qos reset no change
qos stats reset no change
qos flow timeout removed
qos fragment timeout removed
qos port slot/port reset qos port <slot/port[-port]> reset
qos port slot/port [enable | disable] qos port <slot/port[-port]> [enable | disable]
qos port slot/port trusted qos port <slot/port[-port]> trusted
qos port slot/port no trusted qos port <slot/port[-port]> no trusted
qos port slot/port servicing mode {strict-priority | wrr [w0 w1 w2 w3 w4 w5 w6 w7] | prioritywrr [w0 w1 w2 w3 w4 w5 w6 w7] | drr [w0 w1 w2 w3 w4 w5 w6 w7] | default} removed
qos port slot/port qn {minbw | maxbw} kbps removed
qos port slot/port no qn {minbw | maxbw} kbps removed
qos port slot/port maximum bandwidth bps removed
qos port slot/port no maximum bandwidth removed
qos port slot/port maximum egress-bandwidth bps qos port <slot/port[-port]> maximum egress-bandwidth bps
qos port slot/port no maximum egress-bandwidth qos port <slot/port[-port]> no maximum egress-bandwidth
qos port slot/port maximum ingress-bandwidth bps qos port <slot/port[-port]> maximum ingress-bandwidth bps
qos port slot/port no maximum ingress-bandwidth qos port <slot/port[-port]> no maximum ingress-bandwidth
qos port slot/port default 802.1p value qos port <slot/port[-port]> default 802.1p value
qos port slot/port default dscp value qos port <slot/port[-port]> default dscp value
qos port slot/port default classification {802.1p | dscp} qos port <slot/port[-port]> default classification {802.1p | dscp}
qos port slot/port maximum [reserve | signal] bandwidth bps removed
qos port slot/port no maximum [reserve | signal] bandwidth removed
qos port slot/port maximum default buffers <buf> qos port <slot/port[-port]> maximum depth <val>
qos port slot/port no maximum default depth qos port <slot/port[-port]> no maximum depth
qos port slot/port maximum default buffers <buf> removed
qos port slot/port no maximum default buffers removed
show qos port [slot/port] [statistics] removed
show qos queue removed
show qos slice [slot/slice] no change
show qos log no change
show qos config no change
show qos statistics no change
show qos classify removed
policy import <string> removed
policy rule rule_name [enable | disable] [from {ldap | cli}] [precedence precedence] [condition condition] [action action] [validity period name | no validity period] [save] [log [log-interval seconds]] [count {packets | bytes}] [trap | no trap] [default-list | no default-list] policy rule <rule_name> [enable | disable] [from {ldap | cli}] [precedence <precedence>] [condition <condition>] [action <action>] [validity-period <name> | no validity-period] [save] [log [log-interval <seconds>]] [count {packets | bytes}] [trap | no-trap] [default-list]
no policy rule rule_name no change
policy rule rule_name no {reflexive | save | log | default-list | trap | validity-period} no change
policy validity period name [[no] days days] [[no] months months] [[no] hours hh:mm to hh:mm | no hours] [interval mm:dd:yyyy hh:mm to mm:dd:yyyy hh:mm | no interval] policy validity-period <name> [from {ldap | cli} | days <days> | months <months> | hours <hh:mm> to <hh:mm> | interval <mm:dd:yyyy> <hh:mm> to <mm:dd:yyyy> <hh:mm>]
syntax for command above policy validity-period <name> no {hours | interval | days <days> | months <months>}
no policy validity period name no policy validity-period <name>
policy list list_name [type {unp | vrf | ingress | egress | slb}] [from {ldap | cli}] [enable | disable] [rules rule_name [rule_name2...]] no change
policy list list_name [type {unp | vrf | ingress | egress | slb}] [from {ldap | cli}] [enable | disable] no [rules rule_name [rule_name2...]] no change
no policy list list_name no change
policy list list_name no rules rule_name [rule_name2...] no change
policy network group net_group ip_address [from ldap | from cli] [mask net_mask] [ip_address2 [mask net_mask2]...] no change
no policy network group net_group no change
policy network group net_group [from ldap | from cli] no ip_address [mask netmask] [ip_address2 [mask net_mask2]...] no change
policy service group service_group [from ldap | from cli] service_name1 [service_name2...] no change
no policy service group service_group no change
policy service group service_group [from ldap | from cli] no service_name1 [service_name2...] no change
policy mac group mac_group [from ldap | from cli] mac_address [mask mac_mask] [mac_address2 [mask mac_mask2]...] no change
no policy mac group mac_group no change
policy mac group mac_group [from ldap | from cli] no mac_address [mask mac_mask] [mac_address2 [mask mac_mask2]...] no change
policy port group group_name [from ldap | from cli] slot/port[-port] [slot/port[-port]...] no change
no policy port group group_name no change
policy port group group_name [from ldap | from cli] no slot/port[-port] [slot/port[-port]...] no change
policy map group map_group [from ldap | from cli] {value1:value2...} no change
no policy map group map_group no change
policy map group [from ldap | from cli] no {value1:value2...} no change
policy service service_name no change
no policy service service_name no change
policy service service_name protocol protocol {[source ip port port[-port]] [destination ip port port[-port]]} policy service <service_name> protocol <protocol> {[source ip-port <port[-port]>] [destination ip-port <port[-port]>]}
policy service service_name [no source ip port] [no destination ip port] policy service <service_name> no {[source ip-port] [destination ip-port]}
policy service service_name source tcp port port[-port] policy service <service_name> source tcp-port <port[-port]>
policy service service_name no source tcp port policy service <service_name> no source tcp-port
policy service service_name destination tcp port port[-port] policy service <service_name> destination tcp-port <port[-port]>
policy service service_name no destination tcp port policy service <service_name> no destination tcp-port
policy service service_name source udp port port[-port] policy service <service_name> source udp-port <port[-port]>
policy service service_name no source udp port policy service <service_name> no source udp-port
policy service service_name destination udp port port[-port] policy service <service_name> destination udp-port <port[-port]>
policy service service_name no destination udp port policy service <service_name> no destination udp-port
policy condition condition_name no change
no policy condition condition_name no change
policy condition condition_name source ip ip_address [mask netmask] no change
policy condition condition_name no source ip no change
policy condition condition_name source ipv6 {any | ipv6_address [mask netmask]} no change
policy condition condition_name no source ipv6 no change
policy condition condition_name destination ip ip_address [mask netmask] no change
policy condition condition_name no destination ip no change
policy condition condition_name destination ipv6 {any | ipv6_address [mask netmask]} no change
policy condition condition_name no destination ipv6 no change
policy condition condition_name multicast ip ip_address [mask netmask] no change
policy condition condition_name no multicast ip no change
policy condition condition_name multicast ipv6 ip_address [mask netmask] no change
policy condition condition_name no multicast ipv6 no change
policy condition condition_name source network group network_group no change
policy condition condition_name no source network group no change
policy condition condition_name destination network group network_group no change
policy condition condition_name no destination network group no change
policy condition condition_name multicast network group multicast_group no change
policy condition condition_name no multicast network group no change
policy condition condition_name source ip port port[-port] policy condition <condition_name> source ip-port <port[-port]>
policy condition condition_name no source ip port policy condition <condition_name> no source ip-port
policy condition condition_name destination ip port port[-port] policy condition <condition_name> destination ip-port <port[-port]>
policy condition condition_name no destination ip port policy condition <condition_name> no destination ip-port
policy condition condition_name source tcp port port[-port] policy condition <condition_name> source tcp-port <port[-port]>
policy condition condition_name no source tcp port policy condition <condition_name> no source tcp-port
policy condition condition_name destination tcp port port[-port] policy condition <condition_name> destination tcp-port <port[-port]>
policy condition condition_name no destination tcp port policy condition <condition_name> no destination tcp-port
policy condition condition_name source udp port port[-port] policy condition <condition_name> source udp-port <port[-port]>
policy condition condition_name no source udp port policy condition <condition_name> no source udp-port
policy condition condition_name destination udp port port[-port] policy condition <condition_name> destination udp-port <port[-port]>
policy condition condition_name no destination udp port policy condition <condition_name> no destination udp-port
policy condition condition_name ethertype etype no change
policy condition condition_name no ethertype no change
policy condition condition_name established no change
policy condition condition_name no established no change
policy condition condition_name tcpflags [any | all] {F | S | R | P | A | U | E | W} mask {F | S | R | P | A | U | E | W} no change
policy condition condition_name no tcpflags no change
policy condition condition_name service service_name no change
policy condition condition_name no service no change
policy condition condition_name service group service_group no change
policy condition condition_name no service group no change
policy condition condition_name icmptype type no change
policy condition condition_name no icmptype no change
policy condition condition_name icmpcode code no change
policy condition condition_name no icmpcode no change
policy condition condition_name ip protocol protocol policy condition <condition_name> ip-protocol <protocol>
policy condition condition_name no ip protocol policy condition <condition_name> no ip-protocol
policy condition condition_name ipv6 no change
policy condition condition_name no ipv6 no change
policy condition condition_name nh next_header_value no change
policy condition condition_name no nh no change
policy condition condition_name flow-label flow_label_value no change
policy condition condition_name no flow-label no change
policy condition condition_name tos tos_value [mask tos_mask] no change
policy condition conditioning no tos no change
policy condition condition_name dscp {dscp_value[-value]} [mask dscp_mask] no change
policy condition condition_name no dscp no change
policy condition condition_name source mac mac_address [mask mac_mask] no change
policy condition condition_name no source mac no change
policy condition condition_name destination mac mac_address [mask mac_mask] no change
policy condition condition_name no destination mac no change
policy condition condition_name source mac group group_name no change
policy condition condition_name no source mac group no change
policy condition condition_name destination mac group mac_group no change
policy condition condition_name no destination mac group no change
policy condition condition_name source vlan vlan_id no change
policy condition condition_name no source vlan no change
policy condition condition_name inner source vlan vlan_id policy condition <condition_name> inner source-vlan <vlan_id>
policy condition condition_name no inner source vlan policy condition <condition_name> no inner source-vlan
policy condition condition_name destination vlan vlan_id no change
policy condition condition_name no destination vlan no change
policy condition condition_name 802.1p 802.1p_value no change
policy condition condition_name no 802.1p no change
policy condition condition_name inner 802.1p 802.1p_value no change
policy condition condition_name no inner 802.1p no change
policy condition condition_name source port slot/port[-port] no change
policy condition condition_name no source port no change
policy condition condition_name destination port slot/port[-port] no change
policy condition condition_name no destination port no change
policy condition condition_name source port group group_name no change
policy condition condition_name no source port group no change
policy condition condition_name destination port group group_name no change
policy condition condition_name no destination port group no change
policy condition condition_name vrf {vrf_name | default} no change
policy condition condition_name no vrf no change
policy condition condition_name source interface type [ethernet | wan | ethernet-10 | ethernet-100 | ethernet-1G | ethernet-10G] removed
policy condition condition_name no source interface type removed
policy condition condition_name destination interface type [ethernet | wan | ethernet-10 | ethernet-100 | ethernet-1G | ethernet-10G] removed
policy condition condition_name no destination interface type removed
new command policy condition <condition_name> [no] fragments
policy action action_name no change
policy no action action_name no change
policy action action_name disposition {accept | drop | deny} no change
policy action action_name no disposition no change
policy action action_name shared no change
policy action action_name no shared no change
policy action action_name priority priority_value no change
policy action action_name no priority no change
policy action action_name maximum bandwidth bps no change
policy action action_name no maximum bandwidth no change
policy action action_name minimum bandwidth bps removed
policy action action_name no minimum bandwidth removed
policy action action_name maximum depth bytes no change
policy action action_name no maximum depth no change
policy action action_name maximum buffers val removed
policy action action_name no maximum buffers removed
policy action action_name minimum buffers val no change
policy action action_name no minimum buffers no change
policy action action_name minimum depth bytes removed
policy action action_name no minimum depth removed
policy action action_name tos tos_value no change
policy action action_name no tos no change
policy action action_name 802.1p 802.1p_value no change
policy action action_name no 802.1p no change
policy action action_name dscp dscp_value no change
policy action action_name no dscp no change
policy action map {802.1p | tos | dscp} to {802.1p | tos| dscp} using map_group no change
policy action no map no change
policy action action_name permanent gateway ip ip_address policy action <action_name> permanent gateway-ip <ip_address>
policy action action_name no permanent gateway ip policy action <action_name> no permanent gateway-ip
policy action action_name alternate gateway ip ip_address removed
policy action action_name no alternate gateway ip removed
policy action action_name port-disable no change
policy action action_name no port-disable no change
policy action action_name redirect port slot/port no change
policy action action_name no redirect port no change
policy action action_name redirect linkagg link_agg no change
policy action action_name no redirect linkagg no change
policy action action_name no-cache no change
policy action action_name no no-cache no change
policy action action_name [ingress | egress | ingress egress] mirror slot/port no change
policy action action_name no mirror no change
new command policy action <action_name> {pir <rate> | pbs <size> | cir <rate> | cbs <size> | cpu-priority <0-7>}
new command parameter policy action <action_name> cir <rate> cbs <size> [[no] color-only]}
new command parameter policy action <action_name> cir <rate> cbs <size> pir <rate> pbs <size> [[no] color-only]}
show policy classify {l2 | l3 | multicast} [applied] no change
show policy classify {l2 | l3 | multicast} [applied] source port slot/port no change
show policy classify {l2 | l3 | multicast} [applied] destination port slot/port no change
show policy classify {l2 | l3 | multicast} [applied] source mac mac_address no change
show policy classify {l2 | l3 | multicast} [applied] destination mac mac_address no change
show policy classify {l2 | l3 | multicast} [applied] source vlan vlan_id no change
show policy classify {l2 | l3 | multicast} [applied] destination vlan vlan_id no change
show policy classify {l2 | l3 | multicast} [applied] source interface type {ethernet | wan | ethernet-10 | ethernet-100 | ethernet-1G | ethernet-10G} removed
show policy classify {l2 | l3 | multicast} [applied] destination interface type {ethernet | wan | ethernet-10 | ethernet-100 | ethernet-1G | ethernet-10G} removed
show policy classify {l2 | l3 | multicast} [applied] source ip ip_address no change
show policy classify {l2 | l3 | multicast} [applied] destination ip ip_address no change
show policy classify {l2 | l3 | multicast} [applied] multicast ip ip_address no change
show policy classify {l2 | l3 | multicast} [applied] tos tos_value no change
show policy classify {l2 | l3 | multicast} [applied] dscp dscp_value no change
show policy classify {l2 | l3 | multicast} [applied] 802.1p 802.1p_value no change
show policy classify {l2 | l3 | multicast} [applied] ip protocol protocol no change
show policy classify {l2 | l3 | multicast} [applied] source ip port port no change
show policy classify {l2 | l3 | multicast} [applied] destination ip port port no change
show policy classify {l2 | l3 | multicast} [applied] applied no change
show [applied] policy network group [network_group] no change
show [applied] policy service [service_name] no change
show [expanded] [applied] policy service group [service_group] no change
show [applied] policy mac group [mac_group] no change
show [applied] policy port group [group_name] no change
show [applied] policy map group [group_name] no change
show [expanded | verbose] [applied] policy action [action_name] no change
show [expanded | verbose] [applied] policy condition [condition_name] no change
show [expanded | verbose] [applied | active] [bridged | routed | multicast] policy rule [rule_name] no change
show policy validity period [name] show policy validity-period [<name>]
show active policy list [list_name] no change
show [applied] policy list [list_name] no change

RIP

6.4.2.R01 Command 7.1.1.R01 Command
ip load rip no change
ip rip status {enable | disable} ip rip admin-state {enable | disable}
ip rip interface {interface_name} no change
no ip rip interface {interface_name} no change
ip rip interface {interface_name} status {enable | disable} ip rip interface {interface_name} admin-state {enable | disable}
ip rip interface {interface_name} metric value no change
ip rip interface {interface_name} send-version {none | v1 | v1compatible | v2} no change
ip rip interface {interface_name} recv-version {v1 | v2 | both | none} no change
ip rip force-holddowntimer seconds no change
ip rip host-route no change
no ip rip host-route no change
ip rip route-tag value no change
ip rip interface {interface_name} auth-type {none | simple | md5} no change
ip rip interface {interface_name} auth-key string no change
ip rip update-interval seconds no change
ip rip invalid-timer seconds no change
ip rip garbage-timer seconds no change
ip rip holddown-timer seconds no change
show ip rip no change
show ip rip routes [ip_address ip_mask] no change
show ip rip interface [interface_name] no change
show ip rip peer [ip_address] no change
new command ip rip interface {interface_name} ingress-filter [filter_route_map_name]
new command ip rip interface {interface_name} egress-filter [filter_route_map_name]
new command no ip rip interface {interface_name} ingress-filter
new command no ip rip interface {interface_name} egress-filter

SFLOW

6.4.2.R01 Command 7.1.1.R01 Command
sflow agent ip <ip_address> no change
no sflow agent ip <ip_address> no change
sflow receiver <num> [name <string> | timeout {<seconds> | forever} | address {<ip_address> | <ipv6address>} | udp-port <port> | packet-size <size> | Version <num>] sflow receiver <receiver_index> {name <string> | timeout {<seconds> | forever} | address {<ip_address> | <ipv6address>} | udp-port <port> | packet-size <size> Version <num> | release}
sflow receiver <receiver_index> [release] sflow receiver <receiver_index> {name <string> | timeout {<seconds> | forever} | address {<ip_address> | <ipv6address>} | udp-port <port> | packet-size <size> Version <num> | release}
sflow sampler <num> <portlist> [receiver <receiver_index> | rate <value> | sample-hdr-size <size>] sflow sampler <num> port <slot/port[-port]> {receiver <receiver_index> | rate <value> | sample-hdr-size <size>}
no sflow sampler <num> <portlist> no change
sflow poller <num> <portlist> [receiver <receiver_index> | interval <value>] sflow poller <num> port <slot/port[-port]> {receiver <receiver_index> | interval <value>}
no sflow poller <num> <portlist> no change
show sflow agent no change
show sflow receiver [<num>] no change
show sflow sampler [<num>] no change
show sflow poller [<num>] no change

SLB

6.4.2.R01 Command 7.1.1.R01 Command
ip slb admin {enable | disable} ip slb admin-state {enable | disable}
ip slb reset statistics no change
ip slb cluster name {vip ip_address | condition string} [l3 | l2] no change
no ip slb cluster name no change
ip slb cluster cluster_name admin status {enable | disable} ip slb cluster <cluster_name> admin-state {enable | disable}
ip slb cluster cluster_name ping period seconds no change
ip slb cluster cluster_name ping timeout milliseconds no change
ip slb cluster cluster_name ping retries count no change
ip slb cluster cluster_name probe probe_name no change
ip slb server ip ip_address cluster cluster_name [admin status {enable | disable}] ip slb server ip <ip_address> cluster <cluster_name> [admin-state {enable | disable}]
no ip slb server ip ip_address cluster cluster_name no change
ip slb server ip ip_address cluster cluster_name probe probe_name no change
ip slb probe probe_name {ftp | http | https | imap | imaps | nntp | ping | pop | pops | smtp | tcp | udp} no change
no ip slb probe probe_name no change
ip slb probe probe_name {ftp | http | https | imap | imaps | nntp | ping | pop | pops | smtp | tcp | udp} timeout seconds no change
ip slb probe probe_name {ftp | http | https | imap | imaps | nntp | ping | pop | pops | smtp | tcp | udp} period seconds no change
ip slb probe probe_name {ftp | http | https | imap | imaps | nntp | ping | pop | pops | smtp | tcp | udp} port port_number no change
ip slb probe probe_name {ftp | http | https | imap | imaps | nntp | ping | pop | pops | smtp | tcp | udp} retries retries no change
ip slb probe probe_name {http | https} username user_name no change
ip slb probe probe_name {http | https} password password no change
ip slb probe probe_name {http | https} url url no change
ip slb probe probe_name {http | https} status status_value no change
ip slb probe probe_name {tcp | udp} send send_string no change
ip slb probe probe_name {http | https | tcp | udp} expect expect_string no change
show ip slb clusters [statistics] no change
show ip slb cluster name [statistics] no change
show ip slb cluster name server ip_address no change
show ip slb servers no change
show ip slb probes [probe_name] no change

SNMP

6.4.2.R01 Command 7.1.1.R01 Command
SNMP SECURITY {NO SECURITY | AUTHENTICATION {SET | ALL} | PRIVACY {SET | ALL} | TRAP ONLY} snmp security {no-security | authentication {set | all} | privacy {set | all} | trap-only}
SHOW SNMP SECURITY no change
SHOW SNMP STATISTICS no change
SHOW SNMP MIB FAMILY [<string>] show snmp mib-family [<string>]
SNMP AUTHENTICATION TRAP {ENABLE | DISABLE} snmp authentication-trap {enable | disable}
SHOW SNMP AUTHENTICATION TRAP show snmp authentication-trap
SNMP COMMUNITY MAP MODE {ENABLE | DISABLE} snmp community-map mode {enable | disable}
SNMP COMMUNITY MAP <map> {ENABLE | DISABLE} snmp community-map <map> {enable | disable}
SNMP COMMUNITY MAP <map> USER <user> snmp community-map <map> user <user_name>
SNMP COMMUNITY MAP <map> USER <user> {ENABLE | DISABLE} snmp community-map <map> user <user_name> {enable | disable}
NO SNMP COMMUNITY MAP <string> no snmp community-map <map>
SHOW SNMP COMMUNITY MAP show snmp community-map
SHOW SNMP OBJECT NAME <string> no change
SHOW SNMP OBJECT IDENTIFIER <string> no change
SNMP SOURCE IP PREFERRED {DEFAULT | NO-LOOPBACK0 | <ip_address>} snmp source-ip-preferred {default | no-loopback0 | <ip_address>}
NO SNMP SOURCE IP PREFERRED no snmp source-ip-preferred
SNMP STATION <ip_address> {<port> | <user_name> | V1 | V2 | V3 | ENABLE | DISABLE}+ no change
NO SNMP STATION <ip_address> no change
SHOW SNMP STATION no change
SNMP TRAP REPLAY <ip_address> [<seq_id>] snmp-trap replay-ip <ip_address> [<seq_id>]
SNMP TRAP FILTER <ip_address> {<trap_id>}+ snmp-trap filter-ip <ip_address> {<trap_id>}+
NO SNMP TRAP FILTER <ip_address> {<trap_id>}+ no snmp-trap filter-ip <ip_address> {<trap_id>}+
SHOW SNMP TRAP FILTER show snmp-trap filter-ip
SHOW SNMP TRAP REPLAY show snmp-trap replay-ip
SHOW SNMP TRAP CONFIG show snmp-trap config
SNMP TRAP ABSORPTION {ENABLE | DISABLE} snmp-trap absorption {enable | disable}
SNMP TRAP TO WEBVIEW {ENABLE | DISABLE} snmp-trap to-webview {enable | disable}

SOURCE LEARNING

6.4.2.R01 Command 7.1.1.R01 Command
mac-address-table [permanent] mac_address {slot/port | linkagg link_agg} vid [bridging | filtering] mac-learning vlan <vid> {port <slot/port> | linkagg <link_agg>} static mac-address <mac_address> [bridging | filtering]
no mac-address-table [permanent | learned] [mac_address {slot/port | linkagg link_agg} vid] no mac-learning [vlan <vid>] [port <slot/port> | linkagg <link_agg>] {static | dynamic} [mac-address <mac_address>]
mac-address-table static-multicast multicast_address {slot1/port1[-port1a][slot2/port2[| linkagg link_agg} vid mac-learning vlan <vid> {port <slot1/port1[-port1]> <[slot2/port2]> | linkagg <link_agg>} multicast mac-address <multicast_address> [group <groupid>]
no mac-address-table static-multicast [<mac_address> {slot1/port1[-port1a][slot2/port2[| linkagg link_agg} vid] no mac-learning [vlan <vid>] [port <slot1/port1[-port1]> <[slot2/port2]> | linkagg <link_agg>] { multicast } [mac-address <multicast_address>]
source-learning {port <slot/port>|linkagg <agg_num>} enable|disable mac-learning {port <slot/port>| linkagg <link_agg>} {enable|disable}
show source-learning [port slot/port | linkagg link_agg] show mac-learning learning-state [slot <slot> | port <slot/port> | linkagg <link_agg>]
show mac-address-table [permanent | learned | quarantined] [mac_address] [slot slot | slot/port] [linkagg link_agg][vid | vid1-vid2] show mac-learning [summary] [multicast | static | dynamic] [vlan <vid1[-vid2]>] [slot <slot> | port <slot/port>] [linkagg <link_agg>] [mac-address <mac_address>]
show mac-address-table static-multicast [<mac_addr>] [slot slot | slot/port] [linkagg link_agg][vid | vid1-vid2] already included in previous line
show mac-address-table count [mac_address] [slot slot | slot/port] [linkagg link_agg][vid | vid1-vid2] already included in previous line
mac-address-table aging-time <seconds> mac-learning aging-time {<seconds>|default}
no mac-address-table aging-time already included in previous line
source-learning chassis-distributed {enable|disable} mac-learning mode [centralized | distributed]
show source-learning chassis-distributed show mac-learning mode

STP

6.4.2.R01 Command 7.1.1.R01 Command
bridge mode {flat | 1x1} spantree mode {flat | per-vlan}
bridge protocol {stp | rstp | mstp} spantree protocol {stp | rstp | mstp}
bridge <instance> protocol {stp | rstp | mstp} removed
bridge cist protocol {stp | rstp | mstp} spantree cist protocol {stp | rstp | mstp}
bridge 1x1 <vid> protocol {stp | rstp} spantree vlan <vid> protocol {stp | rstp}
bridge mst <msti_id> region name <name> spantree mst <msti_id> region name <name>
bridge mst <msti_id> region no name no spantree mst <msti_id> region name
bridge mst <msti_id> region revision level <rev_level> spantree mst <msti_id> region revision-level <rev_level>
bridge mst <msti_id> region max hops <max_hops> spantree mst <msti_id> region max-hops <max_hops>
bridge msti <msti_id> [name <name>] spantree msti <msti_id> msti_id [name <name>]
bridge no msti <msti_id> no spantree msti <msti_id>
bridge msti <msti_id> no name no spantree msti <msti_id> name
bridge msti <msti_id> vlan <vid_range> spantree msti <msti_id> vlan <vid_range>
bridge msti <msti_id> no vlan <vid_range> no spantree msti <msti_id> vlan <vid_range>
bridge priority <priority> spantree priority <priority>
bridge <instance> priority <priority> removed
bridge cist priority <priority> spantree cist priority <priority>
bridge msti <msti_id> priority <priority> spantree msti <msti_id> priority <priority>
bridge 1x1 <vid> priority <priority> spantree vlan <vid> priority <priority>
bridge hello time <seconds> spantree hello-time <seconds>
bridge <instance> hello time <seconds> removed
bridge cist hello time <seconds> spantree cist hello-time <seconds>
bridge 1x1 vid hello time <seconds> spantree vlan <vid> hello-time <seconds>
bridge max age <seconds> spantree max-age <seconds>
bridge <instance> max age <seconds> removed
bridge cist max age <seconds> spantree cist max-age <seconds>
bridge 1x1<vid> max age <seconds> spantree vlan <vid> max-age <seconds>
bridge forward delay <seconds> spantree forward-delay <seconds>
bridge <instance> forward delay <seconds> removed
bridge cist forward delay <seconds> spantree cist forward-delay <seconds>
bridge 1x1 <vid> forward delay <seconds> spantree vlan <vid> forward-delay <seconds>
bridge bpdu-switching {enable | disable} spantree bpdu-switching {enable | disable}
bridge <instance> bpdu-switching {enable | disable} removed
bridge cist bpdu-switching {enable | disable} spantree cist bpdu-switching {enable | disable}
bridge 1x1 <vid> bpdu-switching {enable | disable} spantree vlan <vid> bpdu-switching {enable | disable}
bridge path cost mode {auto | 32bit} spantree path-cost-mode {auto | 32bit}
bridge [msti <msti_id>] auto-vlan-containment {enable | disable} spantree [msti <msti_id>] auto-vlan-containment {enable | disable}
bridge instance {slot/port | logical_port} {enable | disable} removed
bridge cist {slot/port | logical_port} {enable | disable} spantree cist {port <slot/port1[-port2]> | linkagg <linkagg1[-linkagg2]>} {enable | disable}
bridge 1x1<vid> {slot/port | logical_port} {enable | disable} spantree vlan <vid> {port <slot/port1[-port2]> | linkagg <linkagg1[-linkagg2]>} {enable | disable}
bridge instance {slot/port | logical_port} priority priority removed
bridge cist {slot/port | logical_port} priority priority spantree cist {port <slot/port1[-port2]> | linkagg <linkagg1[-linkagg2]>} priority priority
bridge msti <msti_id> {slot/port | logical_port} priority priority spantree msti <msti_id> {port <slot/port> | linkagg <linkagg1[-linkagg2]>} priority priority
bridge 1x1<vid> {slot/port | logical_port} priority priority spantree vlan <vid> {port <slot/port1[-port2]> | linkagg <linkagg1[-linkagg2]>} priority priority
bridge instance {slot/port | logical_port} path cost path_cost removed
bridge cist {slot/port | logical_port} path cost path_cost spantree cist {port <slot/port1[-port2]> | linkagg <linkagg1[-linkagg2]>} path-cost path_cost
bridge msti <msti_id> {slot/port | logical_port} path cost path_cost spantree msti <msti_id> {port <slot/port> | linkagg <linkagg1[-linkagg2]>} path-cost path_cost
bridge 1x1 <vid> {slot/port | logical_port} path cost path_cost spantree vlan <vid> {port <slot/port1[-port2]> | linkagg <linkagg1[-linkagg2]>} path-cost path_cost
bridge instance {slot/port | logical_port} mode {forwarding | blocking | dynamic} removed
bridge cist {slot/port | logical_port} mode {dynamic | blocking | forwarding} spantree cist {port <slot/port1[-port2]> | linkagg <linkagg1[-linkagg2]>} mode {dynamic | blocking | forwarding}
bridge 1x1 <vid> {slot/port | logical_port} mode {dynamic | blocking | forwarding} spantree vlan <vid> {port <slot/port1[-port2]> | linkagg <linkagg1[-linkagg2]>} mode {dynamic | blocking | forwarding}
bridge instance {slot/port | logical_port} connection {noptp | ptp | autoptp | edgeport} removed
bridge cist {slot/port | logical_port} connection {noptp | ptp | autoptp | edgeport} spantree cist {port <slot/port1[-port2]> | linkagg <linkagg1[-linkagg2]>} connection {noptp | ptp | autoptp}
bridge 1x1 <vid> {slot/port | logical_port} connection {noptp | ptp | autoptp | edgeport} spantree vlan <vid> {port <slot/port1[-port2]> | linkagg <linkagg1[-linkagg2]>} connection {noptp | ptp | autoptp}
bridge cist {slot/port | logical_port} admin-edge {on | off | enable | disable} spantree cist {port <slot/port1[-port2]> | linkagg <linkagg1[-linkagg2]>} admin-edge {enable | disable}
bridge 1x1 <vid> {slot/port | logical_port} admin-edge {on | off | enable | disable} spantree vlan <vid> {port <slot/port1[-port2]> | linkagg <linkagg1[-linkagg2]>} admin-edge {enable | disable}
bridge cist {slot/port | logical_port} auto-edge {on | off | enable | disable} spantree cist {port <slot/port1[-port2]> | linkagg <linkagg1[-linkagg2]>} auto-edge {enable | disable}
bridge 1x1 <vid> {slot/port | logical_port} auto-edge {on | off | enable | disable} spantree vlan <vid> {port <slot/port1[-port2]> | linkagg <linkagg1[-linkagg2]>} auto-edge {enable | disable}
bridge cist {slot/port | logical_port} {restricted-role | root-guard} {on | off | enable | disable} spantree cist {port <slot/port1[-port2]> | linkagg <linkagg1[-linkagg2]>} {restricted-role | root-guard} {enable | disable}
bridge 1x1<vid> {slot/port | logical_port} {restricted-role | root-guard} {on | off | enable | disable} spantree vlan <vid> {port <slot/port1[-port2]> | linkagg <linkagg1[-linkagg2]>} {restricted-role | root-guard} {enable | disable}
bridge cist {slot/port | logical_port} restricted-tcn {on | off | enable | disable} spantree cist {port <slot/port1[-port2]> | linkagg <linkagg1[-linkagg2]>} restricted-tcn {enable | disable}
bridge 1x1<vid> {slot/port | logical_port} restricted-tcn {on | off | enable | disable} spantree vlan <vid> {port <slot/port1[-port2]> | linkagg <linkagg1[-linkagg2]>} restricted-tcn {enable | disable}
bridge cist txholdcount value spantree cist txholdcount value
bridge 1x1<vid> txholdcount {value} spantree vlan <vid> txholdcount {value}
bridge port slot/port 10gig os8800optimized {enable | disable} removed
bridge rrstp removed
no bridge rrstp removed
bridge rrstp ring ring_id port1 {slot/port | linkagg agg_num} port2 {slot/port | linkagg agg_num} vlan-tag vlan_id [status {enable | disable}] removed
no bridge rrstp ring [ring_id] removed
bridge rrstp ring ring_id vlan-tag vid removed
bridge rrstp ring ring_id status {enable | disable} removed
show spantree unchanged
show spantree <instance> removed
show spantree cist unchanged
show spantree msti [msti_id] unchanged
show spantree 1x1 [vid] show spantree [vlan <vid>]
show spantree ports [forwarding | blocking | active | configured] unchanged
show spantree <instance> ports [forwarding | blocking | active | configured] removed
show spantree cist ports [forwarding | blocking | active | configured] unchanged
show spantree msti [msti_id] ports [forwarding | blocking | active | configured] unchanged
show spantree 1x1 [vid] ports [forwarding | blocking | active | configured] show spantree [vlan <vid>] ports [forwarding | blocking | active | configured]
show spantree mst region unchanged
show spantree mst [msti_id] vlan-map unchanged
show spantree cist vlan-map unchanged
show spantree mst vid vlan-map unchanged
show spantree mst port {slot/port | logical_port} show spantree mst {port <slot/port> | linkagg <linkagg1[-linkagg2]>}
show bridge rrstp configuration removed
show bridge rrstp ring [ring_id] removed
show spantree map-msti show spantree [vlan <vlan_id>] map-msti
bridge mode 1x1 pvst+ {enable | disable} spantree pvst+compatibility {enable | disable}
bridge port {slot/port | agg_num} pvst+ {auto | enable | disable} spantree pvst+compatibility {port <slot/port> | linkagg <linkagg1[-linkagg2]>} {enable | disable | auto}

VFC

6.4.2.R01 Command 7.1.1.R01 Command
new command qos wred {wrp-id <1-4> | wrp-name <name>} [color {all | g | y | r} {min <%> | max <%> | pb <%> | gain <1-15>}] [admin-state {enable | disable}]
new command no qos wred {wrp-id <2-4> | wrp-name <name>}
new command show qos wred [wrp-id <1-4> | wrp-name <name>]
new command show qos wred [wrp-id <1-4> | wrp-name <name>] detail [port <slot/port[-port]> | slot <slot> | linkagg <agg[-agg]>]
new command qos qset {qsp-id <1-4> | qsp-name <name>} [wrp-id <1-4> | wpr-name <name>] [wred-admin {enable | disable}] [stats {enable | disable}]
new command show qos qset [qsp-id <1-4> | qsp-name <name>]
new command show qos qset [qsp-id <1-4> | qsp-name <name>] detail [port <slot/port[-port]> | slot <slot> | linkagg <agg[-agg]>]
new command qos qsap {port <slot/port[-port]> | slot <slot> | linkagg <agg[-agg]>} [admin-state {enable | disable}]
new command show qos qsap [port <slot/port[-port]> | slot <slot> | linkagg <agg[-agg]>]
new command show qos qsap [port <slot/port[-port]> | slot <slot> | linkagg <agg[-agg]>] detail
new command qos qsi {port <slot/port[-port]> | slot <slot> | linkagg <agg[-agg]>} [qsp-id <1-4> | qsp-name <name>] [stats {enable | disable}] [wred-admin {enable | disable}]
new command no qos qsi [port <slot/port[-port]> | slot <slot>} | linkagg <agg[-agg]>]
new command clear qos qsap [port <slot/port[-port]> | slot <slot> | linkagg <agg[-agg]>] stats [qp-id <1-8>]
new command show qos qsap [port <slot/port[-port]> | slot <slot> | linkagg <agg[-agg]>] stats [qp-id <1-8>]

VLAN MANAGER

6.4.2.R01 Command 7.1.1.R01 Command
vlan <vid1[-vid2]> 802.1q {<slot/port1[-port2]> | <aggregate_id>} vlan <vid1[-vid2]> members {port <slot/port1[-port2]> | linkagg <agg1[-agg2]>} tagged
no vlan <vid1[-vid2]> 802.1q {<slot/port[-port2]> | <aggregate_id>} no vlan <vid1[-vid2]> members {port <slot/port1[-port2]> | linkagg <agg1[-agg2]>}
vlan <vid> port default {<slot/port> | <link_agg>} vlan <vid> members {port <slot/port1[-port2]> | linkagg <agg1[-agg2]>} untagged
no vlan <vid1[-vid2]> port default {<slot/port> | <link_agg>} no vlan <vid1[-vid2]> members {port <slot/port1[-port2]> | linkagg <agg1[-agg2]>}
vlan <vid1[-vid2]> [enable | disable] vlan <vid1[-vid2]> [admin-state {enable | disable}]
no vlan vid mac mac_address removed
no vlan vid mac range low_mac_address removed
no vlan vid ip ip_address [subnet_mask] removed
no vlan vid ipx ipx_net removed
no vlan vid protocol {ip-e2 | ip-snap | ipx-e2 | ipx-nov | ipx-llc | ipx-snap | decnet | appletalk | ethertype type | dsapssap dsap/ssap | snap snaptype} removed
no vlan vid port slot/port removed
no vlan port mobile slot/port removed
no vlan vid router ipx removed
show vlan [<vid1[-vid2]>] [port [<slot/port> | <link_agg>]] show vlan [<vid1[-vid2]>] [members [port <slot/port1[-port2]> | linkagg <agg1[-agg2]>]]
show vlan router mac-status removed
vlan 802.1q slot/port frame type {all | tagged} removed
show 802.1q {slot/port | aggregate_id} removed
show vlan gvrp [vid1[-vid2]] removed
show vlan ipmvlan [ipmvlan-id1[-ipmvlan-id2]] removed
vlan vid1[-vid2] {1x1 | flat} stp {enable | disable} removed
vlan <vid1[-vid2]> stp {enable | disable} spantree vlan <vid1[-vid2]> admin-state {enable | disable}
vlan vid1[-vid2] mobile-tag {enable | disable} removed
vlan vid router ipx ipx_net [rip | active | inactive | triggered] [e2 | llc | snap | novell] [timeticks ticks] removed

VLAN STACKING

6.4.2.R01 Command 7.1.1.R01 Command
ethernet-service {svlan | ipmvlan | management-vlan} svid1[-svid2] [enable | disable] [[1x1 | flat] stp {enable | disable}] [name description] ethernet-service svlan <svlan1[-svlan2]> [admin-state {enable | disable}] [name <description>] [mtu-ip <size>]
no ethernet-service {svlan | ipmvlan | management-vlan} svid1[-svid2] no ethernet-service svlan <svlan1[-svlan2]>
ethernet-service service-name service-name {svlan | ipmvlan} svid ethernet-service service-name <service-name> svlan <svlan>
no ethernet-service service-name service-name {svlan | ipmvlan} svid no ethernet-service service-name <service-name> svlan <svlan>
ethernet-service svlan svid1[-svid2] nni {slot/port1[-port2] | linkagg agg_num} [stp | erp] ethernet-service svlan <svlan1[-svlan2]> nni {port <slot/port1[-port2]> | linkagg <linkagg1[-linkagg2]>}
no ethernet-service svlan svid1[-svid2] nni {slot/port1[-port2] | linkagg agg_num} no ethernet-service svlan <svlan1[-svlan2]> nni {port <slot/port1[-port2]> | linkagg <linkagg1[-linkagg2]>}
ethernet-service nni {slot/port1[-port2] | agg_num} [tpid value] [{stp | gvrp} legacy-bpdu {enable | disable}] [transparent-bridging {enable | disable}] ethernet-service nni {port <slot/port1[-port2]> | linkagg <linkagg1[-linkagg2]>} [tpid <value>] [{stp | mvrp} legacy-bpdu {enable | disable}]
new command no ethernet-service nni {port <slot/port1[-port2]> | linkagg <linkagg1[-linkagg2]>}
ethernet-service sap sapid service-name service-name no change
no ethernet-service sap sapid no change
ethernet-service sap sapid uni {slot/port1[-port2] | linkagg agg_num} ethernet-service sap <sapid> uni {port <slot/port1[-port2]> | linkagg <linkagg1[-linkagg2]>}
ethernet-service sap sapid no uni {slot/port1[-port2] | linkagg agg_num} no ethernet-service sap <sapid> uni {port <slot/port1[-port2]> | linkagg <linkagg1-[linkagg2]>}
ethernet-service sap sapid cvlan {all | cvid | cvid1-cvid2 | untagged} no change
ethernet-service sap sapid no cvlan {all | cvid | cvid1-cvid2 | untagged} no ethernet-service sap <sapid> cvlan {all | <cvlan1[-cvlan2]> | untagged}
ethernet-service sap-profile sap-profile-name no change
no ethernet-service sap-profile sap-profile-name no change
ethernet-service sap sapid sap-profile sap-profile-name no change
ethernet-service {svlan | ipmvlan} svid1[-svid2] source-learning {enable| disable} removed: use 'mac-learning vlan <vid[-vid]> {enable | disable}'
ethernet-service uni-profile uni-profile-name [l2-protocol {stp | 802.1x | 802.1ab | 802.3ad | gvrp | amap} {peer | discard | tunnel} ethernet-service uni-profile uni-profile-name [l2-protocol {stp | 802.1x | 802.1ab | 802.3ad | amap | mvrp} {peer | discard | tunnel}
no ethernet-service uni-profile uni-profile-name no change
ethernet-service uni {slot/port1[-port2] | agg_num} uni-profile uni-profile-name ethernet-service uni {port <slot/port1[-port2]> | linkagg <linkagg1[-linkagg2]>} uni-profile <uni-profile-name>
show ethernet-service mode removed
show ethernet-services vlan [svid1-[svid2]] no change
show ethernet-service [service-name service-name | svlan svid] no change
show ethernet-services sap [sapid] no change
show ethernet-services port {slot/port | linkagg agg_num} show ethernet-services {port <slot/port> | linkagg <linkagg>}
show ethernet-services nni [slot/port | linkagg agg_num] show ethernet-services nni [port <slot/port> | linkagg <linkagg>]
show ethernet-services uni [slot/port | linkagg agg_num] show ethernet-services uni [port <slot/port> | linkagg <linkagg>]
show ethernet-service uni-profile [uni-profile-name] no change
show ethernet-service sap-profile sap-profile-name no change

VRRP

6.4.2.R01 Command 7.1.1.R01 Command
Optional VRF Prefix on all cmds [vrf {vrf_name}] Optional VRF Prefix on all cmds [vrf {vrf_name}]
vrrp vrid vlan_id [enable | disable | on | off] [priority priority] [preempt | no preempt] [[advertising] interval seconds] no change
no vrrp vrid vlan_id no change
vrrp vrid vlan_id address ip_address no change
vrrp vrid vlan_id no address ip_address no change
vrrp track track_id [enable | disable] [priority value] [ipv4-interface name | ipv6-interface name | port slot/port | address address] no change
no vrrp track track_id no change
vrrp vrid vlan_id track-association track_id no change
vrrp vrid vlan_id no track-association track_id no change
vrrp trap no change
vrrp trap <id> address <ip_address> bfd-std {enable | disable} vrrp trap <id> address <ip_address> bfd-state {enable | disable}
no vrrp trap no change
vrrp delay seconds no change
vrrp3 vrid vlan_id [enable | disable | on | off] [priority priority] [preempt | no preempt][accept | no accept] [[advertising] interval centiseconds] no change
no vrrp3 vrid vlan_id no change
vrrp3 vrid vlan_id address ipv6_address no change
vrrp3 vrid vlan_id no address ipv6_address no change
vrrp3 trap no change
no vrrp3 trap no change
vrrp3 vrid vlan_id track-association track_id no change
vrrp3 vrid vlan_id no track-association track_id no change
show vrrp [vrid] no change
show vrrp [vrid] statistics no change
show vrrp track [track_id] no change
show vrrp [vrid] track-association [track_id] no change
show vrrp3 [vrid] no change
show vrrp3 [vrid] statistics no change
show vrrp3 [vrid] track-association [track_id] no change
aos_release_6_aos_release_7_cli_delta.txt · Zuletzt geändert: 2014/06/18 22:29 von benny